Black Revolink quick release mount with three rubber-coated magnets
White Revolink mount with three rubber-coated magnets fitted, underside view
White Revolink mount with three magnets fitted, angled underside view
Starlink Mini on black Revolink quick release mount, low angle
Black Revolink quick release mount on a Starlink Mini, angled view
Black Revolink quick release mount with cam levers, front view
Starlink Mini Magnetic Mount – Quick Release Mount with Rubber-Coated Magnets
Starlink Mini on black Revolink quick release mount
Starlink Mini on white Revolink quick release mount
Three rubber-coated magnets with M6 threaded studs

Revolink Satellite Gear

Starlink Mini Magnetic Mount – Quick Release Mount with Rubber-Coated Magnets

Sale price$219.99 Regular price$229.98
Save $9.99
SKU: RLK-MAG-QRM-BLK
Color:Black
Quantity:

The Revolink Starlink Mini Magnetic Mount pairs our Quick Release Mount with three rubber-coated magnets for a no-drill install on any flat steel roof, hood or panel. Swap the dish in and out in under 10 seconds, and lift the whole mount off when you're done.

Compatibility

  • Starlink Mini dish
  • Holds on flat steel, bare or painted: car and truck roofs, hoods, steel van and RV panels, steel trailer skins
  • Won't hold on aluminum, fiberglass, carbon or composite, including most truck caps, camper shells and Bronco hardtops

Quick test: if a fridge magnet won't stick, these won't either.

Driving While Installed: Hold depends on a flat, clean steel surface. Confirm all three magnets sit flat and pass a firm pull test before every drive. See the install guide for full instructions.

180 lb Combined Magnetic Hold

Each magnet is rated for 60 lb of pull force. Spaced in a triangle across the mount, the three give 180 lb of combined hold on flat steel.

Scratch-Safe Rubber Coating

A rubber jacket on each magnet protects painted finishes. Set the mount straight down, tilt it to remove, and keep both surfaces clean. Grit is what scratches paint.

Tool-Free Quick Release

Two cam-lever handles clamp the Starlink Mini between the end brackets. Flip them open and the dish lifts out in under 10 seconds, so you can take it inside or move it to another spot without touching the magnets.

Built for the Road

Powder-coated 5052 aluminum frame with stainless steel hardware. Foam-lined brackets hold the dish without rattling. Frame measures 12 × 8.5 × 2 in (305 × 218 × 53 mm).

5-Minute Setup

The magnets bolt through the mount's pre-punched holes with the included washers and M6 nuts. All you need is a 10 mm wrench.

What's Included

  • Revolink Quick Release Mount for Starlink Mini
  • 3 rubber-coated magnets, 60 lb pull each, M6 threaded stems
  • 3 washers and 3 M6 nuts

Need power? Add the Starlink Mini USB-C to Barrel Jack Power Cable or the USB Car Charger.

Revolink Satellite Gear is an independent accessory manufacturer, not affiliated with SpaceX or Starlink. Starlink Mini dish not included.

Presented by Overland Kitted

The Dispatch

INEOS Grenadier at camp fitted with a DVA Mechanics LED side flood light
DVA Mechanics

Gear We Like: DVA Mechanics for the Grenadier

The five DVA Mechanics upgrades our Grenadier customers buy most — from the best-selling Starlink mount to the rear spoiler that turns heads.
MAXTRAX Universal Mounting Pins for MKII XTREME and LITE Boards

MAXTRAX Introduces Universal Mounting Pins for MKII, XTREME, and LITE Boards

MAXTRAX has introduced new Universal Mounting Pins that replace multiple previous pin options with a single standardized system. Designed to work across the MAXTRAX range, the new pins simplify rec...
Colfax Design Works Now Available at Overland Kitted
News

Colfax Design Works Now Available at Overland Kitted

We’re proud to announce that Colfax Design Works is now available at Overland Kitted. Built in the USA, the Colfax Q.D.™ Tire Bag delivers 80 liters of durable, weather-resistant storage with a qui...