{"title":"Mountain Hatch","description":"\u003cp\u003eMountain Hatch builds the original patented food-grade tailgate table: a 1\/2-inch HDPE panel, cut to the shape of your truck's tailgate, that replaces or covers the ribbed factory plastic with a flat, food-safe surface you can prep dinner on, set a stove on, or lean a dirt bike against. Each panel is made to order in Riverside, California, and most fitments are offered in a recessed-pocket version with drink holders and a 1\/4-inch utility tray, or as the original flat panel.\u003c\/p\u003e\u003cp\u003eOverland Kitted carries the full Mountain Hatch range through Shopify Collective: Toyota Tacoma, Tundra, Hilux, Pickup and Land Cruiser 60, 80 and 100 Series; Ford F-150, Super Duty, Ranger and Maverick; Chevy Silverado and GMC Sierra 1500 and HD, Colorado and Canyon; Ram 1500 and HD; Nissan Frontier and Titan; and the Jeep Gladiator, plus the Bear Slapper and Grab n' Go portable cutting boards made from the same material. Pick your truck and model years below, and shop the rest of your setup in \u003ca href=\"\/collections\/tables\"\u003eCamp Tables\u003c\/a\u003e and \u003ca href=\"\/collections\/camp-kitchen\"\u003eCamp Kitchen\u003c\/a\u003e.\u003c\/p\u003e","products":[{"product_id":"toyota-pickup-1st-gen-tacoma-mountain-hatch-1989-2004","title":"Mountain Hatch Tailgate Cutting Board \u0026 Table for 1989-1995 Toyota Pickup \u0026 1995-2004 Tacoma (1st Gen)","description":"\u003cp\u003eThe Mountain Hatch Tailgate Table for the 1989-1995 Toyota Pickup and 1995-2004 first-gen Tacoma gives a thirty-year-old truck a flat, cleanable tailgate for the first time. It is a 1\/2-inch food-grade HDPE panel cut to the compact Toyota tailgate, so the gate that used to be bare stamped steel or a cracked plastic liner becomes a prep counter.\u003c\/p\u003e\u003cp\u003eChoose the flat original or the recessed-pocket version. The two versions differ only on top. The recessed-pocket panel has a pair of drink holders and a 1\/4-inch-deep utility tray molded in; the original flat panel is one clean slab with nothing to work around. On a truck this age the panel also hides a lot of tailgate wear and takes the beating when a dirt bike or a load of firewood slides in. These are built to order in Riverside, California, not pulled off a shelf. The cut is done by machine and the finishing by hand, so expect a production lead before it is ready.\u003c\/p\u003e\u003cp\u003eA few honest notes before you order. HDPE is the same material as a kitchen cutting board, so it will pick up knife marks if you press hard and it gets slick when wet, which matters if the truck is parked on a slope. It is a work surface rather than armor, so it will not stiffen the tailgate. And because the panel adds weight to the gate, Mountain Hatch notes that the factory tailgate damper will let it open a little faster than stock, though it will not slam.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eFits\u003c\/th\u003e\n\u003ctd\u003e1989-1995 Toyota Pickup and 1995-2004 Toyota Tacoma (1st Gen)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eVersions\u003c\/th\u003e\n\u003ctd\u003eRecessed pocket version or Original flat version\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMaterial\u003c\/th\u003e\n\u003ctd\u003eHeavy-duty 1\/2-inch FDA-approved HDPE with UV inhibitors\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSurface\u003c\/th\u003e\n\u003ctd\u003eFood-safe, similar to a commercial cutting board\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eColor\u003c\/th\u003e\n\u003ctd\u003eBlack\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eInstallation\u003c\/th\u003e\n\u003ctd\u003eMounts at the factory tailgate panel locations with the supplied or appropriate hardware.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMade in\u003c\/th\u003e\n\u003ctd\u003eMade to order in Riverside, California, USA\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDesign\u003c\/th\u003e\n\u003ctd\u003eOriginal patented Mountain Hatch tailgate table\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eFitment and ordering\u003c\/h3\u003e\u003cp\u003eThe 2005-2023 Tacoma and 1984-1988 Pickup\/Hilux use their own panels; see \u003ca href=\"\/collections\/mountain-hatch\"\u003eall Mountain Hatch fitments\u003c\/a\u003e. More camp-kitchen surfaces live in \u003ca href=\"\/collections\/tables\"\u003eCamp Tables\u003c\/a\u003e.\u003c\/p\u003e\u003cp\u003e\u003cem\u003eConfirm your tailgate matches the 1989-2004 Toyota compact truck before ordering.\u003c\/em\u003e\u003c\/p\u003e","brand":"Mountain Hatch USA","offers":[{"title":"Black \/ Recessed pocket version","offer_id":50652295463104,"sku":"TOYPICKUP-R-B","price":219.0,"currency_code":"USD","in_stock":true},{"title":"Black \/ Original flat version","offer_id":50652295495872,"sku":"TOYPICKUP-OG-B","price":199.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0525\/3188\/8320\/files\/Screenshot-20241205_200224_Instagram_638c2dbe-8784-4d53-8034-15aa1d0363c3.jpg?v=1793382227"},{"product_id":"toyota-tacoma-mountain-hatch-2024-2027","title":"Mountain Hatch Tailgate Cutting Board \u0026 Table for 2024+ Toyota Tacoma (4th Gen)","description":"\u003cp\u003eMountain Hatch's Tailgate Table for the 2024+ Toyota Tacoma is a fourth-gen-specific panel: a 1\/2-inch HDPE slab cut to the new tailgate's outline, with two drink holders and a 1\/4-inch-deep utility tray molded into the surface. It replaces the factory plastic panel outright rather than sitting on top of it, so the finished gate is one flat, food-safe surface.\u003c\/p\u003e\u003cp\u003eThe recessed layout is what most 4th Gen owners want: a place to park a coffee and a phone while the stove is going, and a tray that catches the small stuff. Removal of the stock panel and installation at the factory mounting locations is the whole job, with no drilling or trimming. Each panel is made to order in Riverside, California: the outline is machine-cut, then the edges and pockets are finished by hand, so allow production time.\u003c\/p\u003e\u003cp\u003eSet expectations before you buy. The surface is textured HDPE, which means it will take knife marks like a kitchen board and is slick when wet. The panel is not structural, so it protects the tailgate skin without reinforcing it. And the added weight lets the factory damper open the gate a touch faster than stock, though, as Mountain Hatch notes, it will not slam open.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eFits\u003c\/th\u003e\n\u003ctd\u003e2024+ Toyota Tacoma (4th Gen), all bed lengths\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eVersions\u003c\/th\u003e\n\u003ctd\u003eRecessed Pocket Version only (drink holders + utility tray)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMaterial\u003c\/th\u003e\n\u003ctd\u003eHeavy-duty 1\/2-inch FDA-approved HDPE with UV inhibitors\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSurface\u003c\/th\u003e\n\u003ctd\u003eFood-safe, similar to a commercial cutting board\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eColor\u003c\/th\u003e\n\u003ctd\u003eBlack\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eInstallation\u003c\/th\u003e\n\u003ctd\u003eRemove the factory tailgate panel and install the Mountain Hatch at the factory mounting locations. No drilling.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMade in\u003c\/th\u003e\n\u003ctd\u003eMade to order in Riverside, California, USA\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDesign\u003c\/th\u003e\n\u003ctd\u003eOriginal patented Mountain Hatch tailgate table\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eFitment and ordering\u003c\/h3\u003e\u003cp\u003ePair it with the rest of the \u003ca href=\"\/collections\/tacoma-4th-gen\"\u003eTacoma 4th Gen\u003c\/a\u003e catalog, or compare it with the other camp surfaces in \u003ca href=\"\/collections\/tables\"\u003eCamp Tables\u003c\/a\u003e. Earlier trucks use the separate 2005-2023 Tacoma panel.\u003c\/p\u003e\u003cp\u003e\u003cem\u003eFitment: 2024+ Toyota Tacoma only.\u003c\/em\u003e\u003c\/p\u003e","brand":"Mountain Hatch USA","offers":[{"title":"Black \/ Recessed Pocket Version New","offer_id":50652295266496,"sku":"4GTACO-R-B","price":249.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0525\/3188\/8320\/files\/rn-image_picker_lib_temp_8e13aa0d-9e05-4b80-96ab-23a1d4d6b5f5.jpg?v=1793382226"},{"product_id":"16-24-nissan-titan-mountain-hatch-tailgate-table","title":"Mountain Hatch Tailgate Cutting Board \u0026 Table for 2016-2024 Nissan Titan","description":"\u003cp\u003eThe Mountain Hatch Tailgate Table for the 2016-2024 Nissan Titan replaces the second-generation Titan's factory tailgate panel with a flat, 1\/2-inch food-grade HDPE counter. Drink holders and a 1\/4-inch-deep utility tray are molded into one end so the rest stays clear for a stove.\u003c\/p\u003e\u003cp\u003eRemove the factory screws and panel, install the Mountain Hatch and reinstall with the appropriate hardware; nothing is drilled. The surface is UV-stabilized and food-safe and protects the gate from gear. Mountain Hatch is a small shop in Riverside, California. Panels are machine-cut, hand-finished and made to order, which means a wait between ordering and the panel being ready.\u003c\/p\u003e\u003cp\u003eTwo trade-offs worth knowing. First, HDPE is cutting-board plastic: it scratches under a hard knife stroke and gets slippery when wet. Second, the panel adds weight to the tailgate, so the factory damper will let the gate drop a little faster than it did; Mountain Hatch is upfront that it stays controlled and does not slam. It is a work surface, not armor, so do not expect it to stiffen the gate.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eFits\u003c\/th\u003e\n\u003ctd\u003e2016-2024 Nissan Titan and Titan XD\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eVersions\u003c\/th\u003e\n\u003ctd\u003eRecessed version with drink holders and utility tray\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMaterial\u003c\/th\u003e\n\u003ctd\u003eHeavy-duty 1\/2-inch FDA-approved HDPE with UV inhibitors\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSurface\u003c\/th\u003e\n\u003ctd\u003eFood-safe, similar to a commercial cutting board\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eColor\u003c\/th\u003e\n\u003ctd\u003eBlack\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eInstallation\u003c\/th\u003e\n\u003ctd\u003eRemove factory screws and OEM tailgate panel, install Mountain Hatch, reinstall with appropriate hardware.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMade in\u003c\/th\u003e\n\u003ctd\u003eMade to order in Riverside, California, USA\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDesign\u003c\/th\u003e\n\u003ctd\u003eOriginal patented Mountain Hatch tailgate table\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eFitment and ordering\u003c\/h3\u003e\u003cp\u003eSee \u003ca href=\"\/collections\/mountain-hatch\"\u003eall Mountain Hatch panels\u003c\/a\u003e or the rest of \u003ca href=\"\/collections\/tables\"\u003eCamp Tables\u003c\/a\u003e.\u003c\/p\u003e\u003cp\u003e\u003cem\u003eFitment: 2016-2024 Nissan Titan. Mountain Hatch lists the Titan; confirm with us for a Titan XD.\u003c\/em\u003e\u003c\/p\u003e","brand":"Mountain Hatch USA","offers":[{"title":"Default Title","offer_id":50652295528640,"sku":"2227FRONTIER-R-B","price":249.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0525\/3188\/8320\/files\/colorado_b8a42261-a0ca-4ca5-b910-59aa4ecb5887.png?v=1793382230"},{"product_id":"19-chevy-silverado-gmc-sierra-1500-mountain-hatch-tailgate-table","title":"Mountain Hatch Tailgate Cutting Board \u0026 Table for 2019+ Chevy Silverado \/ GMC Sierra 1500","description":"\u003cp\u003eThe Mountain Hatch Tailgate Table for the 2019+ Chevy Silverado and GMC Sierra 1500 is a 1\/2-inch food-grade HDPE panel for the T1 trucks' standard tailgate. It replaces the factory insert with a flat counter that has two drink holders and a 1\/4-inch-deep utility tray molded in.\u003c\/p\u003e\u003cp\u003eInstallation uses the factory mounting locations: remove the stock screws and panel, set the Mountain Hatch and reinstall. The surface is food-safe and UV-stabilized, and it protects the gate from the gear you load. Trucks with GM's MultiPro or MultiFlex six-function tailgate have a different tailgate; confirm yours is the standard gate before ordering. Mountain Hatch is a small shop in Riverside, California. Panels are machine-cut, hand-finished and made to order, which means a wait between ordering and the panel being ready.\u003c\/p\u003e\u003cp\u003eTwo trade-offs worth knowing. First, HDPE is cutting-board plastic: it scratches under a hard knife stroke and gets slippery when wet. Second, the panel adds weight to the tailgate, so the factory damper will let the gate drop a little faster than it did; Mountain Hatch is upfront that it stays controlled and does not slam. It is a work surface, not armor, so do not expect it to stiffen the gate.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eFits\u003c\/th\u003e\n\u003ctd\u003e2019+ Chevrolet Silverado 1500 and GMC Sierra 1500 (standard tailgate)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eVersions\u003c\/th\u003e\n\u003ctd\u003eRecessed version with drink holders and utility tray\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMaterial\u003c\/th\u003e\n\u003ctd\u003eHeavy-duty 1\/2-inch FDA-approved HDPE with UV inhibitors\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSurface\u003c\/th\u003e\n\u003ctd\u003eFood-safe, similar to a commercial cutting board\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eColor\u003c\/th\u003e\n\u003ctd\u003eBlack\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eInstallation\u003c\/th\u003e\n\u003ctd\u003eRemove factory screws and OEM tailgate panel, install Mountain Hatch, reinstall with appropriate hardware.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMade in\u003c\/th\u003e\n\u003ctd\u003eMade to order in Riverside, California, USA\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDesign\u003c\/th\u003e\n\u003ctd\u003eOriginal patented Mountain Hatch tailgate table\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eFitment and ordering\u003c\/h3\u003e\u003cp\u003eShop more in \u003ca href=\"\/collections\/silverado-sierra-1500\"\u003eChevy Silverado \/ GMC Sierra 1500 (2019+)\u003c\/a\u003e, or see \u003ca href=\"\/collections\/mountain-hatch\"\u003eall Mountain Hatch panels\u003c\/a\u003e.\u003c\/p\u003e\u003cp\u003e\u003cem\u003eFitment: 2019+ Silverado\/Sierra 1500. Confirm fit on MultiPro \/ MultiFlex tailgates with us before ordering.\u003c\/em\u003e\u003c\/p\u003e","brand":"Mountain Hatch USA","offers":[{"title":"Default Title","offer_id":50652295135424,"sku":"19SILV1500-R-B","price":249.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0525\/3188\/8320\/files\/chevyhatch.png?v=1793382227"},{"product_id":"02-26-ram-hd-mountain-hatch-tailgate-table","title":"Mountain Hatch Tailgate Cutting Board \u0026 Table for 2002-2026 Ram 2500 \/ 3500 HD","description":"\u003cp\u003eMountain Hatch's Tailgate Table for the 2002-2026 Ram 2500 and 3500 HD, Power Wagon included, replaces the factory tailgate panel on the heavy-duty Ram with a flat, 1\/2-inch food-grade HDPE counter. Drink holders and a recessed utility tray are molded into one end.\u003c\/p\u003e\u003cp\u003eRemove the factory screws and panel, install the Mountain Hatch and reinstall; no drilling. On a truck that tows and hauls, the panel is as much tailgate armor against gear and hitches as it is a camp kitchen. Each panel is made to order in Riverside, California: the outline is machine-cut, then the edges and pockets are finished by hand, so allow production time.\u003c\/p\u003e\u003cp\u003eSet expectations before you buy. The surface is textured HDPE, which means it will take knife marks like a kitchen board and is slick when wet. The panel is not structural, so it protects the tailgate skin without reinforcing it. And the added weight lets the factory damper open the gate a touch faster than stock, though, as Mountain Hatch notes, it will not slam open.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eFits\u003c\/th\u003e\n\u003ctd\u003e2002-2026 Ram 2500 and 3500 HD, including Power Wagon, standard tailgate\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eVersions\u003c\/th\u003e\n\u003ctd\u003eRecessed version with drink holders and utility tray\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMaterial\u003c\/th\u003e\n\u003ctd\u003eHeavy-duty 1\/2-inch FDA-approved HDPE with UV inhibitors\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSurface\u003c\/th\u003e\n\u003ctd\u003eFood-safe, similar to a commercial cutting board\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eColor\u003c\/th\u003e\n\u003ctd\u003eBlack\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eInstallation\u003c\/th\u003e\n\u003ctd\u003eRemove factory screws and OEM tailgate panel, install Mountain Hatch, reinstall with appropriate hardware.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMade in\u003c\/th\u003e\n\u003ctd\u003eMade to order in Riverside, California, USA\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDesign\u003c\/th\u003e\n\u003ctd\u003eOriginal patented Mountain Hatch tailgate table\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eFitment and ordering\u003c\/h3\u003e\u003cp\u003eKeep building in \u003ca href=\"\/collections\/ram-hd\"\u003eRAM 2500 \/ 3500 HD\u003c\/a\u003e and \u003ca href=\"\/collections\/ram-power-wagon\"\u003eRAM Power Wagon\u003c\/a\u003e, or see \u003ca href=\"\/collections\/mountain-hatch\"\u003eall Mountain Hatch panels\u003c\/a\u003e.\u003c\/p\u003e\u003cp\u003e\u003cem\u003eFitment: 2002-2026 Ram HD. Mountain Hatch lists one panel across this full span; confirm with us if your tailgate has been changed from stock.\u003c\/em\u003e\u003c\/p\u003e","brand":"Mountain Hatch USA","offers":[{"title":"Default Title","offer_id":50652295561408,"sku":"1926RAMHD-R-B (2500)","price":249.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0525\/3188\/8320\/files\/RAM2.png?v=1793382227"},{"product_id":"19-23-ford-ranger-mountain-hatch-tailgate-table","title":"Mountain Hatch Tailgate Cutting Board \u0026 Table for 2019-2023 Ford Ranger","description":"\u003cp\u003eThe Mountain Hatch Tailgate Table for the 2019-2023 Ford Ranger replaces the factory tailgate panel on the returning midsize Ranger with a flat, 1\/2-inch food-grade HDPE counter. Drink holders and a recessed utility tray are molded in at one end so the stove side stays clear.\u003c\/p\u003e\u003cp\u003eInstallation is a panel swap at the factory mounting locations with no drilling. The surface is food-safe, UV-stabilized and easy to wipe down, and it shields the tailgate from bikes and gear. Mountain Hatch is a small shop in Riverside, California. Panels are machine-cut, hand-finished and made to order, which means a wait between ordering and the panel being ready.\u003c\/p\u003e\u003cp\u003eTwo trade-offs worth knowing. First, HDPE is cutting-board plastic: it scratches under a hard knife stroke and gets slippery when wet. Second, the panel adds weight to the tailgate, so the factory damper will let the gate drop a little faster than it did; Mountain Hatch is upfront that it stays controlled and does not slam. It is a work surface, not armor, so do not expect it to stiffen the gate.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eFits\u003c\/th\u003e\n\u003ctd\u003e2019-2023 Ford Ranger\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eVersions\u003c\/th\u003e\n\u003ctd\u003eRecessed version with drink holders and utility tray\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMaterial\u003c\/th\u003e\n\u003ctd\u003eHeavy-duty 1\/2-inch FDA-approved HDPE with UV inhibitors\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSurface\u003c\/th\u003e\n\u003ctd\u003eFood-safe, similar to a commercial cutting board\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eColor\u003c\/th\u003e\n\u003ctd\u003eBlack\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eInstallation\u003c\/th\u003e\n\u003ctd\u003eRemove factory screws and OEM tailgate panel, install Mountain Hatch, reinstall with appropriate hardware.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMade in\u003c\/th\u003e\n\u003ctd\u003eMade to order in Riverside, California, USA\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDesign\u003c\/th\u003e\n\u003ctd\u003eOriginal patented Mountain Hatch tailgate table\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eFitment and ordering\u003c\/h3\u003e\u003cp\u003eMore for your truck in \u003ca href=\"\/collections\/ford-ranger-2019-2023\"\u003eFord Ranger (2019-2023)\u003c\/a\u003e; 2024+ Rangers use the separate panel. See \u003ca href=\"\/collections\/mountain-hatch\"\u003eall Mountain Hatch panels\u003c\/a\u003e.\u003c\/p\u003e\u003cp\u003e\u003cem\u003eFitment: 2019-2023 Ford Ranger only.\u003c\/em\u003e\u003c\/p\u003e","brand":"Mountain Hatch USA","offers":[{"title":"Default Title","offer_id":50652295200960,"sku":"1922RANGER-R-B","price":249.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0525\/3188\/8320\/files\/RANGER.png?v=1793382228"},{"product_id":"22-27-nissan-frontier-mountain-hatch-tailgate-table","title":"Mountain Hatch Tailgate Cutting Board \u0026 Table for 2022+ Nissan Frontier","description":"\u003cp\u003eMountain Hatch's Tailgate Table for the 2022+ Nissan Frontier fits the redesigned third-generation Frontier with a 1\/2-inch food-grade HDPE panel that replaces the factory tailgate insert. Two drink holders and a recessed utility tray are built into the flat surface.\u003c\/p\u003e\u003cp\u003eFactory screws out, OEM panel off, Mountain Hatch in; no drilling. The UV-stabilized surface is food-safe and tough enough to double as a tailgate protector. Every panel is cut on CNC machinery and then finished by hand in Riverside, California, and built to order, so plan on some production time before it leaves the shop.\u003c\/p\u003e\u003cp\u003eWhat it is not: a rigid reinforcement for the tailgate, or a scratch-proof surface. Like any plastic cutting board it will show knife marks over time, and wet HDPE is slick, so keep an eye on a beer parked on a sloped campsite. The extra weight also means the factory damper lets the gate open a bit quicker than stock; Mountain Hatch says it will not slam, and that matches what owners report.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eFits\u003c\/th\u003e\n\u003ctd\u003e2022+ Nissan Frontier (D41)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eVersions\u003c\/th\u003e\n\u003ctd\u003eRecessed version with drink holders and utility tray\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMaterial\u003c\/th\u003e\n\u003ctd\u003eHeavy-duty 1\/2-inch FDA-approved HDPE with UV inhibitors\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSurface\u003c\/th\u003e\n\u003ctd\u003eFood-safe, similar to a commercial cutting board\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eColor\u003c\/th\u003e\n\u003ctd\u003eBlack\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eInstallation\u003c\/th\u003e\n\u003ctd\u003eRemove factory screws and OEM tailgate panel, install Mountain Hatch, reinstall with appropriate hardware.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMade in\u003c\/th\u003e\n\u003ctd\u003eMade to order in Riverside, California, USA\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDesign\u003c\/th\u003e\n\u003ctd\u003eOriginal patented Mountain Hatch tailgate table\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eFitment and ordering\u003c\/h3\u003e\u003cp\u003eSee \u003ca href=\"\/collections\/mountain-hatch\"\u003eall Mountain Hatch panels\u003c\/a\u003e or the rest of \u003ca href=\"\/collections\/tables\"\u003eCamp Tables\u003c\/a\u003e.\u003c\/p\u003e\u003cp\u003e\u003cem\u003eFitment: 2022+ Nissan Frontier only.\u003c\/em\u003e\u003c\/p\u003e","brand":"Mountain Hatch USA","offers":[{"title":"Default Title","offer_id":50652295332032,"sku":"2227FRONTIER-R-B","price":249.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0525\/3188\/8320\/files\/colorado_2b1d6eb0-efcd-45db-a5ad-63600896ce46.png?v=1793382227"},{"product_id":"bear-slapper-cutting-board","title":"Mountain Hatch Bear Slapper Cutting Board, 12 x 8 in HDPE","description":"\u003cp\u003eThe Mountain Hatch Bear Slapper Cutting Board is a 12 by 8 inch slab of the same food-grade HDPE Mountain Hatch uses for its tailgate tables, with a handle cut into one end. It is the small board that lives in the kitchen box: big enough for an onion, a lime and a block of cheese, small enough to wash in a camp sink.\u003c\/p\u003e\u003cp\u003eHDPE is what commercial kitchens cut on. It does not absorb odors or moisture the way wood does, it will not split, and it scrubs clean with soap and water. The textured black surface shows knife marks over time like any plastic board, and it is not a heat-resistant trivet. The handle doubles as a hang point and, per Mountain Hatch, is for \"easy smacking.\" A sticker is included.\u003c\/p\u003e\u003cp\u003eIt is a natural add-on for a Mountain Hatch tailgate table owner who wants a board to carry to the fire, and a sensible first cutting board for anyone building out a camp kitchen.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eSize\u003c\/th\u003e\n\u003ctd\u003e12 x 8 in\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMaterial\u003c\/th\u003e\n\u003ctd\u003eHeavy-duty FDA-approved food-safe HDPE\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eColor\u003c\/th\u003e\n\u003ctd\u003eBlack\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eHandle\u003c\/th\u003e\n\u003ctd\u003eIntegrated cut-out handle\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eIncluded\u003c\/th\u003e\n\u003ctd\u003eFree Mountain Hatch sticker\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMade in\u003c\/th\u003e\n\u003ctd\u003eUSA\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eGoes with\u003c\/h3\u003e\u003cp\u003ePair it with a \u003ca href=\"\/collections\/mountain-hatch\"\u003eMountain Hatch tailgate table\u003c\/a\u003e, or browse the rest of \u003ca href=\"\/collections\/cookware\"\u003eCookware\u003c\/a\u003e and \u003ca href=\"\/collections\/camp-kitchen\"\u003eCamp Kitchen\u003c\/a\u003e.\u003c\/p\u003e","brand":"Mountain Hatch USA","offers":[{"title":"Default Title","offer_id":50652295430336,"sku":"MH-CB","price":20.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0525\/3188\/8320\/files\/background-editor_output_fedab29d-c60d-44c8-a0c8-59fa0efe1f81.png?v=1793382227"},{"product_id":"60-62-series-mountain-hatch-for-toyota-landcruiser-1980-1990","title":"Mountain Hatch Tailgate Cutting Board \u0026 Table for 1980-1990 Toyota Land Cruiser 60 \u0026 62 Series","description":"\u003cp\u003eThe Mountain Hatch Tailgate Table for the Toyota Land Cruiser 60 and 62 Series is a 1\/2-inch food-grade HDPE panel for the drop-down tailgate on the 1980-1990 FJ60 and FJ62. On a wagon that already serves as a rolling camp kitchen, it gives you a flat, wipe-clean counter at exactly the right height.\u003c\/p\u003e\u003cp\u003eBoth versions are the same $199. The recessed-pocket version adds drink holders and a 1\/4-inch-deep utility tray that keeps a phone, headlamp, knife or onion trimmings from sliding off the gate; the original flat version is one uninterrupted slab for people who want maximum cutting and work area. The panel also protects the original tailgate skin, which matters on a vehicle where replacement sheet metal is hard to find. Mountain Hatch is a small shop in Riverside, California. Panels are machine-cut, hand-finished and made to order, which means a wait between ordering and the panel being ready.\u003c\/p\u003e\u003cp\u003eTwo trade-offs worth knowing. First, HDPE is cutting-board plastic: it scratches under a hard knife stroke and gets slippery when wet. Second, the panel adds weight to the tailgate, so the factory damper will let the gate drop a little faster than it did; Mountain Hatch is upfront that it stays controlled and does not slam. It is a work surface, not armor, so do not expect it to stiffen the gate.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eFits\u003c\/th\u003e\n\u003ctd\u003e1980-1990 Toyota Land Cruiser 60 Series (FJ60) and 62 Series (FJ62)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eVersions\u003c\/th\u003e\n\u003ctd\u003eRecessed pocket version or Original flat version\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMaterial\u003c\/th\u003e\n\u003ctd\u003eHeavy-duty 1\/2-inch FDA-approved HDPE with UV inhibitors\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSurface\u003c\/th\u003e\n\u003ctd\u003eFood-safe, similar to a commercial cutting board\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eColor\u003c\/th\u003e\n\u003ctd\u003eBlack\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eInstallation\u003c\/th\u003e\n\u003ctd\u003eMounts to the tailgate at the factory locations.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMade in\u003c\/th\u003e\n\u003ctd\u003eMade to order in Riverside, California, USA\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDesign\u003c\/th\u003e\n\u003ctd\u003eOriginal patented Mountain Hatch tailgate table\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eFitment and ordering\u003c\/h3\u003e\u003cp\u003e80 Series and 100 Series Land Cruisers have their own panels; see \u003ca href=\"\/collections\/mountain-hatch\"\u003eall Mountain Hatch fitments\u003c\/a\u003e or \u003ca href=\"\/collections\/tables\"\u003eCamp Tables\u003c\/a\u003e.\u003c\/p\u003e\u003cp\u003e\u003cem\u003eFitment: 1980-1990 Land Cruiser 60\/62 Series only.\u003c\/em\u003e\u003c\/p\u003e","brand":"Mountain Hatch USA","offers":[{"title":"Black \/ Recessed pocket version","offer_id":50652295823552,"sku":"LC6062-R-B","price":199.0,"currency_code":"USD","in_stock":true},{"title":"Black \/ Original flat version","offer_id":50652295856320,"sku":"LC6062-OG-B","price":199.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0525\/3188\/8320\/files\/IMG_20230412_163057_758.jpg?v=1793382226"},{"product_id":"02-18-ram-1500-mountain-hatch-tailgate-table","title":"Mountain Hatch Tailgate Cutting Board \u0026 Table for 2002-2018 Ram 1500","description":"\u003cp\u003eMountain Hatch's Tailgate Table for the 2002-2018 Ram 1500 covers the third- and fourth-generation half-ton Ram, including the trucks later sold as the Ram 1500 Classic, with a 1\/2-inch food-grade HDPE panel. Two drink holders and a recessed utility tray are molded into the flat, food-safe surface.\u003c\/p\u003e\u003cp\u003eRemove the factory screws and tailgate panel, install the Mountain Hatch and reinstall with the appropriate hardware; nothing is drilled. The UV-stabilized panel also protects the tailgate from gear and bikes. Every panel is cut on CNC machinery and then finished by hand in Riverside, California, and built to order, so plan on some production time before it leaves the shop.\u003c\/p\u003e\u003cp\u003eWhat it is not: a rigid reinforcement for the tailgate, or a scratch-proof surface. Like any plastic cutting board it will show knife marks over time, and wet HDPE is slick, so keep an eye on a beer parked on a sloped campsite. The extra weight also means the factory damper lets the gate open a bit quicker than stock; Mountain Hatch says it will not slam, and that matches what owners report.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eFits\u003c\/th\u003e\n\u003ctd\u003e2002-2018 Ram 1500 (3rd and 4th Gen)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eVersions\u003c\/th\u003e\n\u003ctd\u003eRecessed version with drink holders and utility tray\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMaterial\u003c\/th\u003e\n\u003ctd\u003eHeavy-duty 1\/2-inch FDA-approved HDPE with UV inhibitors\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSurface\u003c\/th\u003e\n\u003ctd\u003eFood-safe, similar to a commercial cutting board\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eColor\u003c\/th\u003e\n\u003ctd\u003eBlack\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eInstallation\u003c\/th\u003e\n\u003ctd\u003eRemove factory screws and OEM tailgate panel, install Mountain Hatch, reinstall with appropriate hardware.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMade in\u003c\/th\u003e\n\u003ctd\u003eMade to order in Riverside, California, USA\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDesign\u003c\/th\u003e\n\u003ctd\u003eOriginal patented Mountain Hatch tailgate table\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eFitment and ordering\u003c\/h3\u003e\u003cp\u003e2019+ Ram 1500 trucks use the separate panel. See \u003ca href=\"\/collections\/mountain-hatch\"\u003eall Mountain Hatch panels\u003c\/a\u003e or \u003ca href=\"\/collections\/tables\"\u003eCamp Tables\u003c\/a\u003e.\u003c\/p\u003e\u003cp\u003e\u003cem\u003eFitment: 2002-2018 Ram 1500. Confirm your tailgate has the standard factory panel.\u003c\/em\u003e\u003c\/p\u003e","brand":"Mountain Hatch USA","offers":[{"title":"Default Title","offer_id":50652295233728,"sku":"0218RAM-R-B","price":249.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0525\/3188\/8320\/files\/colorado_4e98de3e-3284-4c31-b879-98fff229a297.png?v=1793382227"},{"product_id":"22-26-ford-maverick-mountain-hatch-tailgate-table","title":"Mountain Hatch Tailgate Cutting Board \u0026 Table for 2022-2026 Ford Maverick","description":"\u003cp\u003eThe Mountain Hatch Tailgate Table for the 2022-2026 Ford Maverick is a 1\/2-inch food-grade HDPE panel sized to the compact Maverick tailgate, with two drink holders and a 1\/4-inch-deep utility tray molded in. On a truck with a 4.5-foot bed, a flat tailgate counter is a big share of your usable kitchen.\u003c\/p\u003e\u003cp\u003eInstallation is a swap: factory screws out, OEM panel off, Mountain Hatch in at the stock locations. The surface is food-safe and UV-stabilized, and it protects the gate from bikes and camp gear. Mountain Hatch lists this fitment under U.S. Design Patent D929307. These are built to order in Riverside, California, not pulled off a shelf. The cut is done by machine and the finishing by hand, so expect a production lead before it is ready.\u003c\/p\u003e\u003cp\u003eA few honest notes before you order. HDPE is the same material as a kitchen cutting board, so it will pick up knife marks if you press hard and it gets slick when wet, which matters if the truck is parked on a slope. It is a work surface rather than armor, so it will not stiffen the tailgate. And because the panel adds weight to the gate, Mountain Hatch notes that the factory tailgate damper will let it open a little faster than stock, though it will not slam.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eFits\u003c\/th\u003e\n\u003ctd\u003e2022-2026 Ford Maverick\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eVersions\u003c\/th\u003e\n\u003ctd\u003eRecessed version with drink holders and utility tray\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMaterial\u003c\/th\u003e\n\u003ctd\u003eHeavy-duty 1\/2-inch FDA-approved HDPE with UV inhibitors\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSurface\u003c\/th\u003e\n\u003ctd\u003eFood-safe, similar to a commercial cutting board\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eColor\u003c\/th\u003e\n\u003ctd\u003eBlack\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eInstallation\u003c\/th\u003e\n\u003ctd\u003eRemove factory screws and OEM tailgate panel, install Mountain Hatch, reinstall with appropriate hardware.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMade in\u003c\/th\u003e\n\u003ctd\u003eMade to order in Riverside, California, USA\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDesign\u003c\/th\u003e\n\u003ctd\u003eOriginal patented Mountain Hatch tailgate table\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eFitment and ordering\u003c\/h3\u003e\u003cp\u003eSee \u003ca href=\"\/collections\/mountain-hatch\"\u003eall Mountain Hatch panels\u003c\/a\u003e or the rest of \u003ca href=\"\/collections\/tables\"\u003eCamp Tables\u003c\/a\u003e.\u003c\/p\u003e\u003cp\u003e\u003cem\u003eFitment: 2022-2026 Ford Maverick.\u003c\/em\u003e\u003c\/p\u003e","brand":"Mountain Hatch USA","offers":[{"title":"Default Title","offer_id":50652295626944,"sku":"2226MAVERICK-R-B","price":249.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0525\/3188\/8320\/files\/Maverick.png?v=1793382228"},{"product_id":"17-22-ford-f250-f350-superduty-mountain-hatch-tailgate-table","title":"Mountain Hatch Tailgate Cutting Board \u0026 Table for 2017-2022 Ford F-250 \/ F-350 Super Duty","description":"\u003cp\u003eThe Mountain Hatch Tailgate Table for the 2017-2022 Ford F-250 and F-350 Super Duty is a 1\/2-inch food-grade HDPE panel cut for the aluminum-body fourth-gen Super Duty tailgate. It flattens the ribbed factory insert into a counter with two drink holders and a recessed utility tray.\u003c\/p\u003e\u003cp\u003eInstallation is factory screws out, OEM panel off, Mountain Hatch in. The UV-stabilized surface is food-safe, easy to clean and tough enough to take a generator or a load of gear. These are built to order in Riverside, California, not pulled off a shelf. The cut is done by machine and the finishing by hand, so expect a production lead before it is ready.\u003c\/p\u003e\u003cp\u003eA few honest notes before you order. HDPE is the same material as a kitchen cutting board, so it will pick up knife marks if you press hard and it gets slick when wet, which matters if the truck is parked on a slope. It is a work surface rather than armor, so it will not stiffen the tailgate. And because the panel adds weight to the gate, Mountain Hatch notes that the factory tailgate damper will let it open a little faster than stock, though it will not slam.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eFits\u003c\/th\u003e\n\u003ctd\u003e2017-2022 Ford F-250 and F-350 Super Duty\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eVersions\u003c\/th\u003e\n\u003ctd\u003eRecessed version with drink holders and utility tray\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMaterial\u003c\/th\u003e\n\u003ctd\u003eHeavy-duty 1\/2-inch FDA-approved HDPE with UV inhibitors\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSurface\u003c\/th\u003e\n\u003ctd\u003eFood-safe, similar to a commercial cutting board\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eColor\u003c\/th\u003e\n\u003ctd\u003eBlack\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eInstallation\u003c\/th\u003e\n\u003ctd\u003eRemove factory screws and OEM tailgate panel, install Mountain Hatch, reinstall with appropriate hardware.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMade in\u003c\/th\u003e\n\u003ctd\u003eMade to order in Riverside, California, USA\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDesign\u003c\/th\u003e\n\u003ctd\u003eOriginal patented Mountain Hatch tailgate table\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eFitment and ordering\u003c\/h3\u003e\u003cp\u003eKeep building in \u003ca href=\"\/collections\/super-duty-2017-2022\"\u003eFord Super Duty (2017-2022)\u003c\/a\u003e, or see \u003ca href=\"\/collections\/mountain-hatch\"\u003eall Mountain Hatch panels\u003c\/a\u003e.\u003c\/p\u003e\u003cp\u003e\u003cem\u003eFitment: 2017-2022 Ford Super Duty. Confirm fit if your truck has the factory tailgate step.\u003c\/em\u003e\u003c\/p\u003e","brand":"Mountain Hatch USA","offers":[{"title":"Default Title","offer_id":50652295168192,"sku":"1722SUPERD-R-B","price":249.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0525\/3188\/8320\/files\/f250.png?v=1793382227"},{"product_id":"14-18-chevy-silverado-gmc-sierra-1500-mountain-hatch-tailgate-table","title":"Mountain Hatch Tailgate Cutting Board \u0026 Table for 2014-2018 Chevy Silverado \/ GMC Sierra 1500","description":"\u003cp\u003eMountain Hatch's Tailgate Table for the 2014-2018 Chevy Silverado and GMC Sierra 1500 replaces the factory tailgate panel on the K2XX trucks with a flat, 1\/2-inch food-grade HDPE surface. Drink holders and a recessed utility tray are molded into one end.\u003c\/p\u003e\u003cp\u003eFactory screws out, OEM panel off, Mountain Hatch in at the stock mounting points. The UV-stabilized surface is food-safe, easy to clean and takes a stove or a cooler without marking. Every panel is cut on CNC machinery and then finished by hand in Riverside, California, and built to order, so plan on some production time before it leaves the shop.\u003c\/p\u003e\u003cp\u003eWhat it is not: a rigid reinforcement for the tailgate, or a scratch-proof surface. Like any plastic cutting board it will show knife marks over time, and wet HDPE is slick, so keep an eye on a beer parked on a sloped campsite. The extra weight also means the factory damper lets the gate open a bit quicker than stock; Mountain Hatch says it will not slam, and that matches what owners report.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eFits\u003c\/th\u003e\n\u003ctd\u003e2014-2018 Chevrolet Silverado 1500 and GMC Sierra 1500\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eVersions\u003c\/th\u003e\n\u003ctd\u003eRecessed version with drink holders and utility tray\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMaterial\u003c\/th\u003e\n\u003ctd\u003eHeavy-duty 1\/2-inch FDA-approved HDPE with UV inhibitors\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSurface\u003c\/th\u003e\n\u003ctd\u003eFood-safe, similar to a commercial cutting board\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eColor\u003c\/th\u003e\n\u003ctd\u003eBlack\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eInstallation\u003c\/th\u003e\n\u003ctd\u003eRemove factory screws and OEM tailgate panel, install Mountain Hatch, reinstall with appropriate hardware.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMade in\u003c\/th\u003e\n\u003ctd\u003eMade to order in Riverside, California, USA\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDesign\u003c\/th\u003e\n\u003ctd\u003eOriginal patented Mountain Hatch tailgate table\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eFitment and ordering\u003c\/h3\u003e\u003cp\u003e2019+ trucks use the separate panel. See \u003ca href=\"\/collections\/mountain-hatch\"\u003eall Mountain Hatch panels\u003c\/a\u003e or \u003ca href=\"\/collections\/tables\"\u003eCamp Tables\u003c\/a\u003e.\u003c\/p\u003e\u003cp\u003e\u003cem\u003eFitment: 2014-2018 Silverado\/Sierra 1500 only. Confirm fit if your tailgate has the factory step.\u003c\/em\u003e\u003c\/p\u003e","brand":"Mountain Hatch USA","offers":[{"title":"Default Title","offer_id":50652295594176,"sku":"1518SILV1500-R-B","price":249.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0525\/3188\/8320\/files\/chevyhatch_9e3506c5-e923-4fc0-87d5-be14475ea72a.png?v=1793382228"},{"product_id":"19-26-ram-1500-mountain-hatch-tailgate-table","title":"Mountain Hatch Tailgate Cutting Board \u0026 Table for 2019-2026 Ram 1500 (Old or New Style Tailgate)","description":"\u003cp\u003eThe Mountain Hatch Tailgate Table for the 2019-2026 Ram 1500 is a 1\/2-inch food-grade HDPE panel for the fifth-generation DT truck, with drink holders and a 1\/4-inch-deep utility tray molded in. It is offered in two cuts, Old Style and New Style, because Ram used two different tailgate stampings across these model years.\u003c\/p\u003e\u003cp\u003eOpen your tailgate and compare the inner panel to the two photos in the gallery before you choose: the New Style gate has a cleaner stamped field with round recesses at each end, the Old Style has a long horizontal rib across the top. Installation is the same either way: factory screws out, OEM panel off, Mountain Hatch in. Mountain Hatch is a small shop in Riverside, California. Panels are machine-cut, hand-finished and made to order, which means a wait between ordering and the panel being ready.\u003c\/p\u003e\u003cp\u003eTwo trade-offs worth knowing. First, HDPE is cutting-board plastic: it scratches under a hard knife stroke and gets slippery when wet. Second, the panel adds weight to the tailgate, so the factory damper will let the gate drop a little faster than it did; Mountain Hatch is upfront that it stays controlled and does not slam. It is a work surface, not armor, so do not expect it to stiffen the gate.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eFits\u003c\/th\u003e\n\u003ctd\u003e2019-2026 Ram 1500 (DT), standard tailgate, in Old Style or New Style cut\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eVersions\u003c\/th\u003e\n\u003ctd\u003eRecessed version with drink holders and utility tray; choose Old Style or New Style tailgate\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMaterial\u003c\/th\u003e\n\u003ctd\u003eHeavy-duty 1\/2-inch FDA-approved HDPE with UV inhibitors\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSurface\u003c\/th\u003e\n\u003ctd\u003eFood-safe, similar to a commercial cutting board\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eColor\u003c\/th\u003e\n\u003ctd\u003eBlack\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eInstallation\u003c\/th\u003e\n\u003ctd\u003eRemove factory screws and OEM tailgate panel, install Mountain Hatch, reinstall with appropriate hardware.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMade in\u003c\/th\u003e\n\u003ctd\u003eMade to order in Riverside, California, USA\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDesign\u003c\/th\u003e\n\u003ctd\u003eOriginal patented Mountain Hatch tailgate table\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eFitment and ordering\u003c\/h3\u003e\u003cp\u003eMore for your truck in \u003ca href=\"\/collections\/ram-1500\"\u003eRAM 1500 (2019+)\u003c\/a\u003e, or see \u003ca href=\"\/collections\/mountain-hatch\"\u003eall Mountain Hatch panels\u003c\/a\u003e.\u003c\/p\u003e\u003cp\u003e\u003cem\u003eFitment: 2019-2026 Ram 1500 DT. Match your tailgate to the Old Style \/ New Style photos; ask us if you are unsure, and confirm fit on the 60\/40 Multifunction Tailgate before ordering.\u003c\/em\u003e\u003c\/p\u003e","brand":"Mountain Hatch USA","offers":[{"title":"Old Style","offer_id":50652295364800,"sku":"1926RAM-R-B-1","price":249.0,"currency_code":"USD","in_stock":true},{"title":"New Style","offer_id":50652295397568,"sku":"1926RAM-R-B-2","price":249.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0525\/3188\/8320\/files\/RAM2_515292ec-edee-4016-b9df-11d3d62f5589.png?v=1793382227"},{"product_id":"05-21-nissan-frontier-mountain-hatch-tailgate-table","title":"Mountain Hatch Tailgate Cutting Board \u0026 Table for 2005-2021 Nissan Frontier","description":"\u003cp\u003eThe Mountain Hatch Tailgate Table for the 2005-2021 Nissan Frontier is a 1\/2-inch food-grade HDPE panel for the long-lived D40 Frontier tailgate, with two drink holders and a 1\/4-inch-deep utility tray molded in. It replaces the factory plastic with a flat, food-safe counter.\u003c\/p\u003e\u003cp\u003eInstallation is a swap at the factory mounting locations with no drilling. The surface is UV-stabilized, easy to wipe down and protects the gate when a bike or a cooler goes in. These are built to order in Riverside, California, not pulled off a shelf. The cut is done by machine and the finishing by hand, so expect a production lead before it is ready.\u003c\/p\u003e\u003cp\u003eA few honest notes before you order. HDPE is the same material as a kitchen cutting board, so it will pick up knife marks if you press hard and it gets slick when wet, which matters if the truck is parked on a slope. It is a work surface rather than armor, so it will not stiffen the tailgate. And because the panel adds weight to the gate, Mountain Hatch notes that the factory tailgate damper will let it open a little faster than stock, though it will not slam.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eFits\u003c\/th\u003e\n\u003ctd\u003e2005-2021 Nissan Frontier (D40)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eVersions\u003c\/th\u003e\n\u003ctd\u003eRecessed version with drink holders and utility tray\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMaterial\u003c\/th\u003e\n\u003ctd\u003eHeavy-duty 1\/2-inch FDA-approved HDPE with UV inhibitors\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSurface\u003c\/th\u003e\n\u003ctd\u003eFood-safe, similar to a commercial cutting board\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eColor\u003c\/th\u003e\n\u003ctd\u003eBlack\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eInstallation\u003c\/th\u003e\n\u003ctd\u003eRemove factory screws and OEM tailgate panel, install Mountain Hatch, reinstall with appropriate hardware.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMade in\u003c\/th\u003e\n\u003ctd\u003eMade to order in Riverside, California, USA\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDesign\u003c\/th\u003e\n\u003ctd\u003eOriginal patented Mountain Hatch tailgate table\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eFitment and ordering\u003c\/h3\u003e\u003cp\u003e2022+ Frontiers use the separate panel. See \u003ca href=\"\/collections\/mountain-hatch\"\u003eall Mountain Hatch panels\u003c\/a\u003e or \u003ca href=\"\/collections\/tables\"\u003eCamp Tables\u003c\/a\u003e.\u003c\/p\u003e\u003cp\u003e\u003cem\u003eFitment: 2005-2021 Nissan Frontier only.\u003c\/em\u003e\u003c\/p\u003e","brand":"Mountain Hatch USA","offers":[{"title":"Default Title","offer_id":50652295725248,"sku":"0521FRONTIER-R-B","price":249.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0525\/3188\/8320\/files\/colorado_7745a361-4cb8-497c-a9fa-fa47a43ce950.png?v=1793382228"},{"product_id":"22-silverado-sierra-2500-3500-hd-mountain-hatch-tailgate-table","title":"Mountain Hatch Tailgate Cutting Board \u0026 Table for 2022+ Chevy Silverado \/ GMC Sierra 2500 \u0026 3500 HD","description":"\u003cp\u003eMountain Hatch's Tailgate Table for the 2022+ Chevy Silverado and GMC Sierra 2500 and 3500 HD gives the heavy-duty GM tailgate a flat, 1\/2-inch food-grade HDPE surface with drink holders and a recessed utility tray. It replaces the factory panel at the stock mounting locations.\u003c\/p\u003e\u003cp\u003eRemove the factory screws and panel, install the Mountain Hatch and reinstall; no drilling. On an HD truck the panel does double duty as a tailgate protector when the trailer gear and tools go in. As with the 1500, confirm you have the standard tailgate rather than the MultiPro or MultiFlex gate. Each panel is made to order in Riverside, California: the outline is machine-cut, then the edges and pockets are finished by hand, so allow production time.\u003c\/p\u003e\u003cp\u003eSet expectations before you buy. The surface is textured HDPE, which means it will take knife marks like a kitchen board and is slick when wet. The panel is not structural, so it protects the tailgate skin without reinforcing it. And the added weight lets the factory damper open the gate a touch faster than stock, though, as Mountain Hatch notes, it will not slam open.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eFits\u003c\/th\u003e\n\u003ctd\u003e2022+ Chevrolet Silverado 2500\/3500 HD and GMC Sierra 2500\/3500 HD (standard tailgate)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eVersions\u003c\/th\u003e\n\u003ctd\u003eRecessed version with drink holders and utility tray\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMaterial\u003c\/th\u003e\n\u003ctd\u003eHeavy-duty 1\/2-inch FDA-approved HDPE with UV inhibitors\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSurface\u003c\/th\u003e\n\u003ctd\u003eFood-safe, similar to a commercial cutting board\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eColor\u003c\/th\u003e\n\u003ctd\u003eBlack\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eInstallation\u003c\/th\u003e\n\u003ctd\u003eRemove factory screws and OEM tailgate panel, install Mountain Hatch, reinstall with appropriate hardware.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMade in\u003c\/th\u003e\n\u003ctd\u003eMade to order in Riverside, California, USA\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDesign\u003c\/th\u003e\n\u003ctd\u003eOriginal patented Mountain Hatch tailgate table\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eFitment and ordering\u003c\/h3\u003e\u003cp\u003eSee \u003ca href=\"\/collections\/mountain-hatch\"\u003eall Mountain Hatch panels\u003c\/a\u003e or \u003ca href=\"\/collections\/tables\"\u003eCamp Tables\u003c\/a\u003e.\u003c\/p\u003e\u003cp\u003e\u003cem\u003eFitment: 2022+ GM 2500\/3500 HD with the standard tailgate. Ask us before ordering for a MultiPro \/ MultiFlex gate.\u003c\/em\u003e\u003c\/p\u003e","brand":"Mountain Hatch USA","offers":[{"title":"Default Title","offer_id":50652295299264,"sku":"22SILV2500-R-B","price":249.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0525\/3188\/8320\/files\/chevyhatch_5ef1adfe-b918-4238-a9b0-44049ae19b98.png?v=1793382228"},{"product_id":"toyota-tacoma-mountain-hatch-2005-2023","title":"Mountain Hatch Tailgate Cutting Board \u0026 Table for 2005-2023 Toyota Tacoma (2nd \u0026 3rd Gen)","description":"\u003cp\u003eThe Mountain Hatch Tailgate Table for the 2005-2023 Toyota Tacoma is the product that started the brand: a 1\/2-inch sheet of food-grade HDPE, cut to the shape of the second- and third-gen Tacoma tailgate, that turns the ribbed factory plastic into a flat prep counter. It is the least expensive panel in the Mountain Hatch range and the one with the longest track record on Tacomas.\u003c\/p\u003e\u003cp\u003ePick the version that matches how you camp. The recessed-pocket version adds drink holders and a 1\/4-inch-deep utility tray that keeps a phone, headlamp, knife or onion trimmings from sliding off the gate; the original flat version is one uninterrupted slab for people who want maximum cutting and work area. Either way you get a surface that shrugs off a Jetboil, a camp stove or a cooler, is easy to wipe down, and uses the factory tailgate panel's mounting points, so there is no drilling. Mountain Hatch is a small shop in Riverside, California. Panels are machine-cut, hand-finished and made to order, which means a wait between ordering and the panel being ready.\u003c\/p\u003e\u003cp\u003eTwo trade-offs worth knowing. First, HDPE is cutting-board plastic: it scratches under a hard knife stroke and gets slippery when wet. Second, the panel adds weight to the tailgate, so the factory damper will let the gate drop a little faster than it did; Mountain Hatch is upfront that it stays controlled and does not slam. It is a work surface, not armor, so do not expect it to stiffen the gate.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eFits\u003c\/th\u003e\n\u003ctd\u003e2005-2015 Toyota Tacoma (2nd Gen) and 2016-2023 Toyota Tacoma (3rd Gen)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eVersions\u003c\/th\u003e\n\u003ctd\u003eRecessed Pocket Version (drink holders + 1\/4 in utility tray) or The OG Version, flat\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMaterial\u003c\/th\u003e\n\u003ctd\u003eHeavy-duty 1\/2-inch FDA-approved HDPE with UV inhibitors\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSurface\u003c\/th\u003e\n\u003ctd\u003eFood-safe, similar to a commercial cutting board\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eColor\u003c\/th\u003e\n\u003ctd\u003eBlack\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eInstallation\u003c\/th\u003e\n\u003ctd\u003eFastens at the factory tailgate panel mounting locations; Mountain Hatch says it installs over the OEM insert. No drilling.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMade in\u003c\/th\u003e\n\u003ctd\u003eMade to order in Riverside, California, USA\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDesign\u003c\/th\u003e\n\u003ctd\u003eOriginal patented Mountain Hatch tailgate table\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eFitment and ordering\u003c\/h3\u003e\u003cp\u003eThis panel fits every 2005-2023 Tacoma, long bed or short bed. Shop the rest of your truck in \u003ca href=\"\/collections\/tacoma-2nd-gen\"\u003eTacoma 2nd Gen\u003c\/a\u003e and \u003ca href=\"\/collections\/tacoma-3rd-gen\"\u003eTacoma 3rd Gen\u003c\/a\u003e, or browse \u003ca href=\"\/collections\/mountain-hatch\"\u003eall Mountain Hatch panels\u003c\/a\u003e. 2024+ owners need the separate 4th Gen panel.\u003c\/p\u003e\u003cp\u003e\u003cem\u003eFitment: 2005-2023 Toyota Tacoma only. Confirm your model year before ordering; the 2024+ Tacoma uses a different tailgate.\u003c\/em\u003e\u003c\/p\u003e","brand":"Mountain Hatch USA","offers":[{"title":"Black \/ Recessed Pocket Version","offer_id":50652295921856,"sku":"2G3GTACO-R-B","price":199.0,"currency_code":"USD","in_stock":true},{"title":"Black \/ The OG Version Just Flat No Frills","offer_id":50652295954624,"sku":"2G3GTACO-OG-B","price":199.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0525\/3188\/8320\/files\/rn-image_picker_lib_temp_bed1e737-da01-44ca-b064-9212a85b1834.jpg?v=1793382227"},{"product_id":"toyota-tundra-mountain-hatch-1999-2006","title":"Mountain Hatch Tailgate Cutting Board \u0026 Table for 1999-2006 Toyota Tundra (1st Gen)","description":"\u003cp\u003eMountain Hatch's Tailgate Table for the 1999-2006 Toyota Tundra is cut in two widths, because the first-gen Tundra used a narrower bed on the Regular and Access Cab than it did on the 2004-2006 Double Cab. Pick the size that matches your truck and you get a flat, 1\/2-inch food-grade HDPE panel in place of the factory tailgate surface.\u003c\/p\u003e\u003cp\u003eBoth widths come in the flat original or the recessed-pocket version. Go recessed if you cook on the gate: that version molds in two drink holders and a shallow, 1\/4-inch-deep tray for the small things that otherwise roll away. Go flat if you would rather have every square inch available as cutting and work surface. It is a practical upgrade on a truck whose factory tailgate has usually seen twenty years of use. Each panel is made to order in Riverside, California: the outline is machine-cut, then the edges and pockets are finished by hand, so allow production time.\u003c\/p\u003e\u003cp\u003eSet expectations before you buy. The surface is textured HDPE, which means it will take knife marks like a kitchen board and is slick when wet. The panel is not structural, so it protects the tailgate skin without reinforcing it. And the added weight lets the factory damper open the gate a touch faster than stock, though, as Mountain Hatch notes, it will not slam open.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eFits\u003c\/th\u003e\n\u003ctd\u003e1999-2006 Toyota Tundra (1st Gen): Single Cab \/ Extra (Access) Cab, or Double Cab\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eVersions\u003c\/th\u003e\n\u003ctd\u003eOriginal flat version or Recessed pocket version, in two tailgate widths\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMaterial\u003c\/th\u003e\n\u003ctd\u003eHeavy-duty 1\/2-inch FDA-approved HDPE with UV inhibitors\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSurface\u003c\/th\u003e\n\u003ctd\u003eFood-safe, similar to a commercial cutting board\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eColor\u003c\/th\u003e\n\u003ctd\u003eBlack\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eInstallation\u003c\/th\u003e\n\u003ctd\u003eMounts at the factory tailgate panel locations.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMade in\u003c\/th\u003e\n\u003ctd\u003eMade to order in Riverside, California, USA\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDesign\u003c\/th\u003e\n\u003ctd\u003eOriginal patented Mountain Hatch tailgate table\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eFitment and ordering\u003c\/h3\u003e\u003cp\u003e2007-2021 and 2022+ Tundras use their own panels; see \u003ca href=\"\/collections\/mountain-hatch\"\u003eall Mountain Hatch fitments\u003c\/a\u003e or \u003ca href=\"\/collections\/tables\"\u003eCamp Tables\u003c\/a\u003e.\u003c\/p\u003e\u003cp\u003e\u003cem\u003eMeasure or confirm your cab configuration: the Double Cab tailgate is wider than the Regular\/Access Cab tailgate.\u003c\/em\u003e\u003c\/p\u003e","brand":"Mountain Hatch USA","offers":[{"title":"Single Cab \/ Extra Cab \/ Black \/ Original flat version","offer_id":50652295987392,"sku":"1GTUNDRA-OG-B","price":249.0,"currency_code":"USD","in_stock":true},{"title":"Single Cab \/ Extra Cab \/ Black \/ Recessed pocket version","offer_id":50652296020160,"sku":"1GTUNDRA-R-B","price":249.0,"currency_code":"USD","in_stock":true},{"title":"Double Cab \/ Black \/ Original flat version","offer_id":50652296052928,"sku":"1GTUNDRA-DC-OG-B","price":259.0,"currency_code":"USD","in_stock":true},{"title":"Double Cab \/ Black \/ Recessed pocket version","offer_id":50652296085696,"sku":"1GTUNDRA-DC-R-B","price":269.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0525\/3188\/8320\/files\/IMG-3328_cd259954-936a-4229-bf6c-f62ac71ef5c3.jpg?v=1793382226"},{"product_id":"toyota-pickup-hilux-mountain-hatch-1984-1988","title":"Mountain Hatch Tailgate Cutting Board \u0026 Table for 1984-1988 Toyota Pickup \/ Hilux","description":"\u003cp\u003eMountain Hatch's Tailgate Table for the 1984-1988 Toyota Pickup, sold as the Hilux outside North America, is a 1\/2-inch HDPE panel cut for the fourth-generation compact Toyota tailgate. It is the panel for the solid-axle-era trucks that still get driven, not just shown.\u003c\/p\u003e\u003cp\u003eBoth versions are offered. Recessed or flat is the one decision to make. Recessed gives you two drink holders and a 1\/4-inch-deep catch tray for a phone, knife or trimmings; flat gives you the whole panel as an uninterrupted cutting surface. The material is UV-stabilized and food-safe, and the panel is thick enough to double as tailgate protection when the truck is working. Every panel is cut on CNC machinery and then finished by hand in Riverside, California, and built to order, so plan on some production time before it leaves the shop.\u003c\/p\u003e\u003cp\u003eWhat it is not: a rigid reinforcement for the tailgate, or a scratch-proof surface. Like any plastic cutting board it will show knife marks over time, and wet HDPE is slick, so keep an eye on a beer parked on a sloped campsite. The extra weight also means the factory damper lets the gate open a bit quicker than stock; Mountain Hatch says it will not slam, and that matches what owners report.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eFits\u003c\/th\u003e\n\u003ctd\u003e1984-1988 Toyota Pickup \/ Hilux\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eVersions\u003c\/th\u003e\n\u003ctd\u003eRecessed pocket version or Original flat version\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMaterial\u003c\/th\u003e\n\u003ctd\u003eHeavy-duty 1\/2-inch FDA-approved HDPE with UV inhibitors\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSurface\u003c\/th\u003e\n\u003ctd\u003eFood-safe, similar to a commercial cutting board\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eColor\u003c\/th\u003e\n\u003ctd\u003eBlack\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eInstallation\u003c\/th\u003e\n\u003ctd\u003eMounts at the factory tailgate panel locations.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMade in\u003c\/th\u003e\n\u003ctd\u003eMade to order in Riverside, California, USA\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDesign\u003c\/th\u003e\n\u003ctd\u003eOriginal patented Mountain Hatch tailgate table\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eFitment and ordering\u003c\/h3\u003e\u003cp\u003e1989-2004 Toyota Pickup and 1st Gen Tacoma owners need the separate 1989-2004 panel; see \u003ca href=\"\/collections\/mountain-hatch\"\u003eall Mountain Hatch panels\u003c\/a\u003e or \u003ca href=\"\/collections\/tables\"\u003eCamp Tables\u003c\/a\u003e.\u003c\/p\u003e\u003cp\u003e\u003cem\u003eFitment: 1984-1988 Toyota Pickup \/ Hilux only.\u003c\/em\u003e\u003c\/p\u003e","brand":"Mountain Hatch USA","offers":[{"title":"Black \/ Recessed pocket version","offer_id":50652295758016,"sku":"4GHILUX-R-B","price":239.0,"currency_code":"USD","in_stock":true},{"title":"Black \/ Original flat version","offer_id":50652295790784,"sku":"4GHILUX-R-OG","price":229.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0525\/3188\/8320\/files\/Screenshot-20231224_203003_Instagram_ec1b2fe6-f90c-4a0d-b87a-6b8d4b44646e.jpg?v=1793382227"},{"product_id":"15-22-chevy-colorado-gmc-canyon-mountain-hatch-tailgate-table","title":"Mountain Hatch Tailgate Cutting Board \u0026 Table for 2015-2022 Chevy Colorado \/ GMC Canyon","description":"\u003cp\u003eThe Mountain Hatch Tailgate Table for the 2015-2022 Chevy Colorado and GMC Canyon turns the second-gen midsize GM tailgate into a flat, 1\/2-inch food-grade HDPE counter with two drink holders and a 1\/4-inch-deep utility tray. It replaces the factory tailgate panel at the stock screw locations.\u003c\/p\u003e\u003cp\u003eInstallation is the usual Mountain Hatch swap with no drilling. The UV-stabilized surface is food-safe and easy to wipe down, and it protects the gate when a bike or cooler slides in. These are built to order in Riverside, California, not pulled off a shelf. The cut is done by machine and the finishing by hand, so expect a production lead before it is ready.\u003c\/p\u003e\u003cp\u003eA few honest notes before you order. HDPE is the same material as a kitchen cutting board, so it will pick up knife marks if you press hard and it gets slick when wet, which matters if the truck is parked on a slope. It is a work surface rather than armor, so it will not stiffen the tailgate. And because the panel adds weight to the gate, Mountain Hatch notes that the factory tailgate damper will let it open a little faster than stock, though it will not slam.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eFits\u003c\/th\u003e\n\u003ctd\u003e2015-2022 Chevrolet Colorado and GMC Canyon (2nd Gen)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eVersions\u003c\/th\u003e\n\u003ctd\u003eRecessed version with drink holders and utility tray\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMaterial\u003c\/th\u003e\n\u003ctd\u003eHeavy-duty 1\/2-inch FDA-approved HDPE with UV inhibitors\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSurface\u003c\/th\u003e\n\u003ctd\u003eFood-safe, similar to a commercial cutting board\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eColor\u003c\/th\u003e\n\u003ctd\u003eBlack\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eInstallation\u003c\/th\u003e\n\u003ctd\u003eRemove factory screws and OEM tailgate panel, install Mountain Hatch, reinstall with appropriate hardware.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMade in\u003c\/th\u003e\n\u003ctd\u003eMade to order in Riverside, California, USA\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDesign\u003c\/th\u003e\n\u003ctd\u003eOriginal patented Mountain Hatch tailgate table\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eFitment and ordering\u003c\/h3\u003e\u003cp\u003eShop the rest of \u003ca href=\"\/collections\/colorado-canyon-2015-2022\"\u003eChevy Colorado \/ GMC Canyon (2015-2022)\u003c\/a\u003e, or see \u003ca href=\"\/collections\/mountain-hatch\"\u003eall Mountain Hatch panels\u003c\/a\u003e.\u003c\/p\u003e\u003cp\u003e\u003cem\u003eFitment: 2015-2022 Colorado\/Canyon only; the 2023+ truck is a different tailgate.\u003c\/em\u003e\u003c\/p\u003e","brand":"Mountain Hatch USA","offers":[{"title":"Default Title","offer_id":50652295692480,"sku":"1522COLO-R-B","price":249.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0525\/3188\/8320\/files\/colorado.png?v=1793382227"},{"product_id":"19-27-jeep-gladiator-mountain-hatch-tailgate-table","title":"Mountain Hatch Tailgate Cutting Board \u0026 Table for 2020+ Jeep Gladiator JT","description":"\u003cp\u003eMountain Hatch's Tailgate Table for the Jeep Gladiator JT is a 1\/2-inch food-grade HDPE panel that replaces the factory tailgate insert with a flat, food-safe counter. Two drink holders and a recessed utility tray are molded in, which on a 5-foot bed is a meaningful amount of kitchen.\u003c\/p\u003e\u003cp\u003eInstallation is the standard swap at the factory mounting locations with no drilling. The UV-stabilized surface wipes clean and protects the gate when the bikes go in. Mountain Hatch lists the fitment as 2019-2027; the Gladiator launched as a 2020 model and the tailgate is unchanged through the current truck. Each panel is made to order in Riverside, California: the outline is machine-cut, then the edges and pockets are finished by hand, so allow production time.\u003c\/p\u003e\u003cp\u003eSet expectations before you buy. The surface is textured HDPE, which means it will take knife marks like a kitchen board and is slick when wet. The panel is not structural, so it protects the tailgate skin without reinforcing it. And the added weight lets the factory damper open the gate a touch faster than stock, though, as Mountain Hatch notes, it will not slam open.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eFits\u003c\/th\u003e\n\u003ctd\u003eJeep Gladiator JT (2020+; Mountain Hatch lists 2019-2027)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eVersions\u003c\/th\u003e\n\u003ctd\u003eRecessed version with drink holders and utility tray\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMaterial\u003c\/th\u003e\n\u003ctd\u003eHeavy-duty 1\/2-inch FDA-approved HDPE with UV inhibitors\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSurface\u003c\/th\u003e\n\u003ctd\u003eFood-safe, similar to a commercial cutting board\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eColor\u003c\/th\u003e\n\u003ctd\u003eBlack\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eInstallation\u003c\/th\u003e\n\u003ctd\u003eRemove factory screws and OEM tailgate panel, install Mountain Hatch, reinstall with appropriate hardware.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMade in\u003c\/th\u003e\n\u003ctd\u003eMade to order in Riverside, California, USA\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDesign\u003c\/th\u003e\n\u003ctd\u003eOriginal patented Mountain Hatch tailgate table\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eFitment and ordering\u003c\/h3\u003e\u003cp\u003eShop more in \u003ca href=\"\/collections\/gladiator-jt\"\u003eJeep Gladiator JT (2020+)\u003c\/a\u003e, or see \u003ca href=\"\/collections\/mountain-hatch\"\u003eall Mountain Hatch panels\u003c\/a\u003e.\u003c\/p\u003e\u003cp\u003e\u003cem\u003eFitment: Jeep Gladiator JT with the standard tailgate (not the Trail Rail bed-management tailgate inserts).\u003c\/em\u003e\u003c\/p\u003e","brand":"Mountain Hatch USA","offers":[{"title":"Default Title","offer_id":50652295889088,"sku":"1727GLADIATOR-R-B","price":249.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0525\/3188\/8320\/files\/JeepHatch.png?v=1793382227"},{"product_id":"toyota-hilux-mountain-hatch-2015-2023","title":"Mountain Hatch Tailgate Cutting Board \u0026 Table for 2015-2023 Toyota Hilux","description":"\u003cp\u003eThe Mountain Hatch Tailgate Table for the 2015-2023 Toyota Hilux brings the brand's food-grade tailgate panel to the eighth-generation Hilux, the truck the rest of the world drives instead of a Tacoma. It is 1\/2-inch HDPE cut to the Hilux tailgate and the only Mountain Hatch panel offered in two colors.\u003c\/p\u003e\u003cp\u003eChoose Black or Smoke Grey, and the recessed-pocket or flat version. The recessed-pocket version adds drink holders and a 1\/4-inch-deep utility tray that keeps a phone, headlamp, knife or onion trimmings from sliding off the gate; the original flat version is one uninterrupted slab for people who want maximum cutting and work area. The surface is UV-stabilized, so a grey panel will not turn chalky in the sun the way painted steel does. Mountain Hatch is a small shop in Riverside, California. Panels are machine-cut, hand-finished and made to order, which means a wait between ordering and the panel being ready.\u003c\/p\u003e\u003cp\u003eTwo trade-offs worth knowing. First, HDPE is cutting-board plastic: it scratches under a hard knife stroke and gets slippery when wet. Second, the panel adds weight to the tailgate, so the factory damper will let the gate drop a little faster than it did; Mountain Hatch is upfront that it stays controlled and does not slam. It is a work surface, not armor, so do not expect it to stiffen the gate.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eFits\u003c\/th\u003e\n\u003ctd\u003e2015-2023 Toyota Hilux\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eVersions\u003c\/th\u003e\n\u003ctd\u003eRecessed pocket version or Original flat version, in Black or Smoke Grey\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMaterial\u003c\/th\u003e\n\u003ctd\u003eHeavy-duty 1\/2-inch FDA-approved HDPE with UV inhibitors\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSurface\u003c\/th\u003e\n\u003ctd\u003eFood-safe, similar to a commercial cutting board\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eColor\u003c\/th\u003e\n\u003ctd\u003eBlack or Smoke Grey\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eInstallation\u003c\/th\u003e\n\u003ctd\u003eMounts at the factory tailgate panel locations.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMade in\u003c\/th\u003e\n\u003ctd\u003eMade to order in Riverside, California, USA\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDesign\u003c\/th\u003e\n\u003ctd\u003eOriginal patented Mountain Hatch tailgate table\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eFitment and ordering\u003c\/h3\u003e\u003cp\u003eBrowse \u003ca href=\"\/collections\/mountain-hatch\"\u003eall Mountain Hatch panels\u003c\/a\u003e or the rest of \u003ca href=\"\/collections\/tables\"\u003eCamp Tables\u003c\/a\u003e.\u003c\/p\u003e\u003cp\u003e\u003cem\u003eFitment: 2015-2023 Toyota Hilux. The Hilux is not sold in the US market; confirm your tailgate before ordering.\u003c\/em\u003e\u003c\/p\u003e","brand":"Mountain Hatch USA","offers":[{"title":"Black \/ Recessed pocket version","offer_id":50652296249536,"sku":"7GHILUX-R-B","price":259.0,"currency_code":"USD","in_stock":true},{"title":"Black \/ Original flat version","offer_id":50652296282304,"sku":"7GHILUX-OG-B","price":259.0,"currency_code":"USD","in_stock":true},{"title":"Smoke Grey \/ Recessed pocket version","offer_id":50652296315072,"sku":"7GHILUX-R-SG","price":259.0,"currency_code":"USD","in_stock":true},{"title":"Smoke Grey \/ Original flat version","offer_id":50652296347840,"sku":"7GHILUX-OG-SG","price":259.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0525\/3188\/8320\/files\/Screenshot-20240121_013751_Instagram.jpg?v=1793382227"},{"product_id":"05-14-ford-f150-mountain-hatch-tailgate-table","title":"Mountain Hatch Tailgate Cutting Board \u0026 Table for 2005-2014 Ford F-150","description":"\u003cp\u003eMountain Hatch's Tailgate Table for the 2005-2014 Ford F-150 replaces the ribbed factory tailgate panel on eleventh- and twelfth-generation trucks with a flat, 1\/2-inch food-grade HDPE surface. Two drink holders and a 1\/4-inch-deep utility tray are molded in, so the gate becomes a usable kitchen counter, not just a bench.\u003c\/p\u003e\u003cp\u003eInstallation is a panel swap: remove the factory screws and OEM panel, set the Mountain Hatch in its place and reinstall with the appropriate hardware. No drilling, no trimming. The surface is food-safe and UV-stabilized, and it protects the tailgate when a dirt bike or a load of lumber goes in. Every panel is cut on CNC machinery and then finished by hand in Riverside, California, and built to order, so plan on some production time before it leaves the shop.\u003c\/p\u003e\u003cp\u003eWhat it is not: a rigid reinforcement for the tailgate, or a scratch-proof surface. Like any plastic cutting board it will show knife marks over time, and wet HDPE is slick, so keep an eye on a beer parked on a sloped campsite. The extra weight also means the factory damper lets the gate open a bit quicker than stock; Mountain Hatch says it will not slam, and that matches what owners report.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eFits\u003c\/th\u003e\n\u003ctd\u003e2005-2014 Ford F-150 (11th and 12th Gen)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eVersions\u003c\/th\u003e\n\u003ctd\u003eRecessed version with drink holders and utility tray\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMaterial\u003c\/th\u003e\n\u003ctd\u003eHeavy-duty 1\/2-inch FDA-approved HDPE with UV inhibitors\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSurface\u003c\/th\u003e\n\u003ctd\u003eFood-safe, similar to a commercial cutting board\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eColor\u003c\/th\u003e\n\u003ctd\u003eBlack\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eInstallation\u003c\/th\u003e\n\u003ctd\u003eRemove factory screws and OEM tailgate panel, install Mountain Hatch, reinstall with appropriate hardware. No drilling.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMade in\u003c\/th\u003e\n\u003ctd\u003eMade to order in Riverside, California, USA\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDesign\u003c\/th\u003e\n\u003ctd\u003eOriginal patented Mountain Hatch tailgate table\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eFitment and ordering\u003c\/h3\u003e\u003cp\u003e2015+ trucks use the separate 2015-2026 F-150 panel. See \u003ca href=\"\/collections\/mountain-hatch\"\u003eall Mountain Hatch panels\u003c\/a\u003e or \u003ca href=\"\/collections\/tables\"\u003eCamp Tables\u003c\/a\u003e.\u003c\/p\u003e\u003cp\u003e\u003cem\u003eFitment: 2005-2014 Ford F-150 only.\u003c\/em\u003e\u003c\/p\u003e","brand":"Mountain Hatch USA","offers":[{"title":"Default Title","offer_id":50652295659712,"sku":"0514F150-R-B","price":249.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0525\/3188\/8320\/files\/F150_hatcj.png?v=1793382226"},{"product_id":"80-series-lx-450-mountain-hatch-toyota-landcruiser-1991-1997","title":"Mountain Hatch Tailgate Cutting Board \u0026 Table for 1991-1997 Toyota Land Cruiser 80 Series \/ Lexus LX 450","description":"\u003cp\u003eMountain Hatch's Tailgate Table for the 1991-1997 Toyota Land Cruiser 80 Series, and the Lexus LX 450 that shares its body, replaces the factory carpeted tailgate surface with a 1\/2-inch food-grade HDPE panel. The carpet on an 80 is usually the first thing to go; this is the answer that also makes the gate a prep counter.\u003c\/p\u003e\u003cp\u003ePick flat or recessed. Go recessed if you cook on the gate: that version molds in two drink holders and a shallow, 1\/4-inch-deep tray for the small things that otherwise roll away. Go flat if you would rather have every square inch available as cutting and work surface. Mountain Hatch offers new fasteners with the panel for 80 Series builds where the originals are tired. Each panel is made to order in Riverside, California: the outline is machine-cut, then the edges and pockets are finished by hand, so allow production time.\u003c\/p\u003e\u003cp\u003eSet expectations before you buy. The surface is textured HDPE, which means it will take knife marks like a kitchen board and is slick when wet. The panel is not structural, so it protects the tailgate skin without reinforcing it. And the added weight lets the factory damper open the gate a touch faster than stock, though, as Mountain Hatch notes, it will not slam open.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eFits\u003c\/th\u003e\n\u003ctd\u003e1991-1997 Toyota Land Cruiser 80 Series (FZJ80\/FJ80) and 1996-1997 Lexus LX 450\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eVersions\u003c\/th\u003e\n\u003ctd\u003eRecessed pocket version or Original flat version\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMaterial\u003c\/th\u003e\n\u003ctd\u003eHeavy-duty 1\/2-inch FDA-approved HDPE with UV inhibitors\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSurface\u003c\/th\u003e\n\u003ctd\u003eFood-safe, similar to a commercial cutting board\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eColor\u003c\/th\u003e\n\u003ctd\u003eBlack\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eInstallation\u003c\/th\u003e\n\u003ctd\u003eReplaces the factory carpeted tailgate surface at the stock mounting points; new fasteners available with purchase.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMade in\u003c\/th\u003e\n\u003ctd\u003eMade to order in Riverside, California, USA\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDesign\u003c\/th\u003e\n\u003ctd\u003eOriginal patented Mountain Hatch tailgate table\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eFitment and ordering\u003c\/h3\u003e\u003cp\u003eShop the rest of your rig in \u003ca href=\"\/collections\/land-cruiser-80-series\"\u003eLand Cruiser 80 Series\u003c\/a\u003e, or see \u003ca href=\"\/collections\/mountain-hatch\"\u003eall Mountain Hatch panels\u003c\/a\u003e.\u003c\/p\u003e\u003cp\u003e\u003cem\u003eFitment: 1991-1997 Land Cruiser 80 Series and Lexus LX 450.\u003c\/em\u003e\u003c\/p\u003e","brand":"Mountain Hatch USA","offers":[{"title":"Black \/ Recessed pocket version","offer_id":50652296380608,"sku":"LC80-R-B","price":249.0,"currency_code":"USD","in_stock":true},{"title":"Black \/ Original flat version","offer_id":50652296413376,"sku":"LC-OG-B","price":239.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0525\/3188\/8320\/files\/rn-image_picker_lib_temp_5a638751-c2ec-4448-9b4d-21d8edd0045a.jpg?v=1793382227"},{"product_id":"99-16-ford-f250-f350-superduty-mountain-hatch-tailgate-table","title":"Mountain Hatch Tailgate Cutting Board \u0026 Table for 1999-2016 Ford F-250 \/ F-350 Super Duty","description":"\u003cp\u003eMountain Hatch's Tailgate Table for the 1999-2016 Ford F-250 and F-350 Super Duty is a 1\/2-inch food-grade HDPE panel for the long-running first- through third-generation Super Duty tailgate. It replaces the factory plastic with a flat, food-safe counter that has drink holders and a 1\/4-inch-deep utility tray molded in.\u003c\/p\u003e\u003cp\u003eRemove the factory screws and panel, drop the Mountain Hatch into place and reinstall; no drilling is involved. On a working truck the panel earns its keep as a tailgate protector as much as a kitchen counter. Each panel is made to order in Riverside, California: the outline is machine-cut, then the edges and pockets are finished by hand, so allow production time.\u003c\/p\u003e\u003cp\u003eSet expectations before you buy. The surface is textured HDPE, which means it will take knife marks like a kitchen board and is slick when wet. The panel is not structural, so it protects the tailgate skin without reinforcing it. And the added weight lets the factory damper open the gate a touch faster than stock, though, as Mountain Hatch notes, it will not slam open.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eFits\u003c\/th\u003e\n\u003ctd\u003e1999-2016 Ford F-250 and F-350 Super Duty\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eVersions\u003c\/th\u003e\n\u003ctd\u003eRecessed version with drink holders and utility tray\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMaterial\u003c\/th\u003e\n\u003ctd\u003eHeavy-duty 1\/2-inch FDA-approved HDPE with UV inhibitors\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSurface\u003c\/th\u003e\n\u003ctd\u003eFood-safe, similar to a commercial cutting board\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eColor\u003c\/th\u003e\n\u003ctd\u003eBlack\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eInstallation\u003c\/th\u003e\n\u003ctd\u003eRemove factory screws and OEM tailgate panel, install Mountain Hatch, reinstall with appropriate hardware.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMade in\u003c\/th\u003e\n\u003ctd\u003eMade to order in Riverside, California, USA\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDesign\u003c\/th\u003e\n\u003ctd\u003eOriginal patented Mountain Hatch tailgate table\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eFitment and ordering\u003c\/h3\u003e\u003cp\u003e2017+ Super Duty trucks use separate panels. See \u003ca href=\"\/collections\/mountain-hatch\"\u003eall Mountain Hatch panels\u003c\/a\u003e or \u003ca href=\"\/collections\/tables\"\u003eCamp Tables\u003c\/a\u003e.\u003c\/p\u003e\u003cp\u003e\u003cem\u003eFitment: 1999-2016 Ford Super Duty. Confirm your tailgate has the standard factory panel.\u003c\/em\u003e\u003c\/p\u003e","brand":"Mountain Hatch USA","offers":[{"title":"Default Title","offer_id":50652296577216,"sku":"9916SUPERD-R-B","price":249.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0525\/3188\/8320\/files\/F150_hatcj_8497fd50-2c6c-4763-90a6-3a230c7734f2.png?v=1793382227"},{"product_id":"toyota-tundra-mountain-hatch-2007-2021","title":"Mountain Hatch Tailgate Cutting Board \u0026 Table for 2007-2021 Toyota Tundra (2nd Gen)","description":"\u003cp\u003eThe Mountain Hatch Tailgate Table for the 2007-2021 Toyota Tundra is a full-width, 1\/2-inch HDPE panel for the second-generation truck, and it covers the entire 2007-2021 run including the 2014 refresh. A Tundra tailgate is a big piece of real estate; this makes it flat and food-safe.\u003c\/p\u003e\u003cp\u003eThe two versions differ only on top. The recessed-pocket panel has a pair of drink holders and a 1\/4-inch-deep utility tray molded in; the original flat panel is one clean slab with nothing to work around. Mountain Hatch says the panel installs over the factory tailgate insert at the stock mounting locations. These are built to order in Riverside, California, not pulled off a shelf. The cut is done by machine and the finishing by hand, so expect a production lead before it is ready.\u003c\/p\u003e\u003cp\u003eA few honest notes before you order. HDPE is the same material as a kitchen cutting board, so it will pick up knife marks if you press hard and it gets slick when wet, which matters if the truck is parked on a slope. It is a work surface rather than armor, so it will not stiffen the tailgate. And because the panel adds weight to the gate, Mountain Hatch notes that the factory tailgate damper will let it open a little faster than stock, though it will not slam.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eFits\u003c\/th\u003e\n\u003ctd\u003e2007-2021 Toyota Tundra (2nd Gen), all cabs and bed lengths\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eVersions\u003c\/th\u003e\n\u003ctd\u003eRecessed pocket version or Original flat version\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMaterial\u003c\/th\u003e\n\u003ctd\u003eHeavy-duty 1\/2-inch FDA-approved HDPE with UV inhibitors\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSurface\u003c\/th\u003e\n\u003ctd\u003eFood-safe, similar to a commercial cutting board\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eColor\u003c\/th\u003e\n\u003ctd\u003eBlack\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eInstallation\u003c\/th\u003e\n\u003ctd\u003eInstalls over the factory OEM tailgate insert at the stock mounting locations.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMade in\u003c\/th\u003e\n\u003ctd\u003eMade to order in Riverside, California, USA\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDesign\u003c\/th\u003e\n\u003ctd\u003eOriginal patented Mountain Hatch tailgate table\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eFitment and ordering\u003c\/h3\u003e\u003cp\u003eShop the rest of your truck in \u003ca href=\"\/collections\/tundra-2nd-gen\"\u003eTundra 2nd Gen\u003c\/a\u003e, or see \u003ca href=\"\/collections\/mountain-hatch\"\u003eall Mountain Hatch panels\u003c\/a\u003e.\u003c\/p\u003e\u003cp\u003e\u003cem\u003eFitment: 2007-2021 Toyota Tundra only.\u003c\/em\u003e\u003c\/p\u003e","brand":"Mountain Hatch USA","offers":[{"title":"Color Black New \/ Recessed pocket version","offer_id":50652296511680,"sku":"2GTUNDRA-R-B","price":269.0,"currency_code":"USD","in_stock":true},{"title":"Color Black New \/ Original flat version","offer_id":50652296544448,"sku":"2GTUNDRA-OG-B","price":249.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0525\/3188\/8320\/files\/TUNDRAUSE.png?v=1793382228"},{"product_id":"grab-n-go-portable-cutting-board","title":"Mountain Hatch Grab n' Go Portable HDPE Cutting Board, 22-52 in","description":"\u003cp\u003eThe Mountain Hatch Grab n' Go is the tailgate table without the tailgate: a long, 12.8-inch-tall slab of food-grade HDPE with Mountain Hatch's recessed square tray and round drink holder molded in, in four lengths from 22 to 52 inches. It sits on a drawer system, a fridge slide, a camp table or the ground, and it packs flat against the bed wall when you are done.\u003c\/p\u003e\u003cp\u003ePick the length for the job. The 22 inch is a one-person prep board; the 32 and 42 inch sizes span most drawer tops and fridge slides, which is where Mountain Hatch photographs them; the 52 inch is a full camp-kitchen counter for a group. All four are the same heavy-duty, UV-stabilized, FDA-approved HDPE as the tailgate panels, so they wipe clean and will not absorb odors, though they will show knife marks over time and are slick when wet.\u003c\/p\u003e\u003cp\u003eIt is the right choice if your truck has a tailgate Mountain Hatch does not cut for, if you run a canopy camper with a drawer system, or if you want a second surface to go with the panel on your tailgate.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eSizes\u003c\/th\u003e\n\u003ctd\u003e22, 32, 42 or 52 in long, 12.8 in tall\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eFeatures\u003c\/th\u003e\n\u003ctd\u003eRecessed square utility tray and round drink holder\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMaterial\u003c\/th\u003e\n\u003ctd\u003eHeavy-duty food-grade HDPE with UV inhibitors\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eColor\u003c\/th\u003e\n\u003ctd\u003eBlack\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eInstallation\u003c\/th\u003e\n\u003ctd\u003eNone; portable\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMade in\u003c\/th\u003e\n\u003ctd\u003eUSA\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eGoes with\u003c\/h3\u003e\u003cp\u003eSee the vehicle-specific \u003ca href=\"\/collections\/mountain-hatch\"\u003eMountain Hatch tailgate tables\u003c\/a\u003e, or browse \u003ca href=\"\/collections\/drawer-systems\"\u003eCargo + Drawer Systems\u003c\/a\u003e and \u003ca href=\"\/collections\/camp-kitchen\"\u003eCamp Kitchen\u003c\/a\u003e.\u003c\/p\u003e","brand":"Mountain Hatch USA","offers":[{"title":"Grab n' Go 52","offer_id":50652296118464,"sku":"GG52","price":119.99,"currency_code":"USD","in_stock":true},{"title":"Grab n' Go 42","offer_id":50652296151232,"sku":"GG42","price":99.99,"currency_code":"USD","in_stock":true},{"title":"Grab n' Go 32","offer_id":50652296184000,"sku":"GG32","price":69.99,"currency_code":"USD","in_stock":true},{"title":"Grab n' Go 22","offer_id":50652296216768,"sku":"GG22","price":49.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0525\/3188\/8320\/files\/GrabnGo1.png?v=1793382227"},{"product_id":"toyota-tundra-mountain-hatch-2022-2026","title":"Mountain Hatch Tailgate Cutting Board \u0026 Table for 2022+ Toyota Tundra (3rd Gen)","description":"\u003cp\u003eMountain Hatch's Tailgate Table for the 2022+ Toyota Tundra turns the third-gen truck's tailgate into a flat, 1\/2-inch food-grade HDPE counter. It installs over the factory tailgate insert using the stock mounting locations, so the hybrid-era Tundra's tailgate hardware and camera stay exactly where Toyota put them.\u003c\/p\u003e\u003cp\u003eOrder it flat or with recessed pockets. Recessed or flat is the one decision to make. Recessed gives you two drink holders and a 1\/4-inch-deep catch tray for a phone, knife or trimmings; flat gives you the whole panel as an uninterrupted cutting surface. The UV-stabilized surface wipes clean, takes a stove or a cooler without complaint, and protects the factory panel underneath when gear slides in. Every panel is cut on CNC machinery and then finished by hand in Riverside, California, and built to order, so plan on some production time before it leaves the shop.\u003c\/p\u003e\u003cp\u003eWhat it is not: a rigid reinforcement for the tailgate, or a scratch-proof surface. Like any plastic cutting board it will show knife marks over time, and wet HDPE is slick, so keep an eye on a beer parked on a sloped campsite. The extra weight also means the factory damper lets the gate open a bit quicker than stock; Mountain Hatch says it will not slam, and that matches what owners report.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eFits\u003c\/th\u003e\n\u003ctd\u003e2022+ Toyota Tundra (3rd Gen), all cabs and bed lengths\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eVersions\u003c\/th\u003e\n\u003ctd\u003eRecessed pocket version or Original flat version\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMaterial\u003c\/th\u003e\n\u003ctd\u003eHeavy-duty 1\/2-inch FDA-approved HDPE with UV inhibitors\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSurface\u003c\/th\u003e\n\u003ctd\u003eFood-safe, similar to a commercial cutting board\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eColor\u003c\/th\u003e\n\u003ctd\u003eBlack\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eInstallation\u003c\/th\u003e\n\u003ctd\u003eInstalls over the factory OEM tailgate insert at the stock mounting locations.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMade in\u003c\/th\u003e\n\u003ctd\u003eMade to order in Riverside, California, USA\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDesign\u003c\/th\u003e\n\u003ctd\u003eOriginal patented Mountain Hatch tailgate table\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eFitment and ordering\u003c\/h3\u003e\u003cp\u003eKeep building in \u003ca href=\"\/collections\/tundra-3rd-gen\"\u003eTundra 3rd Gen\u003c\/a\u003e, or compare with other \u003ca href=\"\/collections\/tables\"\u003eCamp Tables\u003c\/a\u003e.\u003c\/p\u003e\u003cp\u003e\u003cem\u003eFitment: 2022+ Toyota Tundra only.\u003c\/em\u003e\u003c\/p\u003e","brand":"Mountain Hatch USA","offers":[{"title":"Color Black New \/ Recessed pocket version","offer_id":50652296446144,"sku":"3GTUNDRA-R-B","price":269.0,"currency_code":"USD","in_stock":true},{"title":"Color Black New \/ Original flat version","offer_id":50652296478912,"sku":"3GTUNDRA-OG-B","price":259.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0525\/3188\/8320\/files\/TUNDRAUSE22.png?v=1793382227"},{"product_id":"100-series-mountain-hatch-for-toyota-landcruiser-lx-470-1998-2007","title":"Mountain Hatch Tailgate Cutting Board \u0026 Table for 1998-2007 Toyota Land Cruiser 100 Series \/ Lexus LX 470","description":"\u003cp\u003eThe Mountain Hatch Tailgate Table for the 1998-2007 Toyota Land Cruiser 100 Series and Lexus LX 470 swaps the carpeted factory tailgate surface for a flat, 1\/2-inch food-grade HDPE panel. It turns the 100's drop-down gate into a camp counter you can cut on, cook on and hose off.\u003c\/p\u003e\u003cp\u003eBoth versions are offered. The two versions differ only on top. The recessed-pocket panel has a pair of drink holders and a 1\/4-inch-deep utility tray molded in; the original flat panel is one clean slab with nothing to work around. The material is UV-stabilized and the panel protects the tailgate skin when fridges and recovery gear get dragged across it. New fasteners are available with the panel. These are built to order in Riverside, California, not pulled off a shelf. The cut is done by machine and the finishing by hand, so expect a production lead before it is ready.\u003c\/p\u003e\u003cp\u003eA few honest notes before you order. HDPE is the same material as a kitchen cutting board, so it will pick up knife marks if you press hard and it gets slick when wet, which matters if the truck is parked on a slope. It is a work surface rather than armor, so it will not stiffen the tailgate. And because the panel adds weight to the gate, Mountain Hatch notes that the factory tailgate damper will let it open a little faster than stock, though it will not slam.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eFits\u003c\/th\u003e\n\u003ctd\u003e1998-2007 Toyota Land Cruiser 100 Series (UZJ100) and Lexus LX 470\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eVersions\u003c\/th\u003e\n\u003ctd\u003eRecessed pocket version or Original flat version\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMaterial\u003c\/th\u003e\n\u003ctd\u003eHeavy-duty 1\/2-inch FDA-approved HDPE with UV inhibitors\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSurface\u003c\/th\u003e\n\u003ctd\u003eFood-safe, similar to a commercial cutting board\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eColor\u003c\/th\u003e\n\u003ctd\u003eBlack\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eInstallation\u003c\/th\u003e\n\u003ctd\u003eReplaces the factory carpeted tailgate surface at the stock mounting points; new fasteners available with purchase.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMade in\u003c\/th\u003e\n\u003ctd\u003eMade to order in Riverside, California, USA\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDesign\u003c\/th\u003e\n\u003ctd\u003eOriginal patented Mountain Hatch tailgate table\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eFitment and ordering\u003c\/h3\u003e\u003cp\u003eKeep building in \u003ca href=\"\/collections\/land-cruiser-100-series\"\u003eLand Cruiser 100 Series\u003c\/a\u003e, or browse \u003ca href=\"\/collections\/mountain-hatch\"\u003eall Mountain Hatch panels\u003c\/a\u003e.\u003c\/p\u003e\u003cp\u003e\u003cem\u003eFitment: 1998-2007 Land Cruiser 100 Series and Lexus LX 470.\u003c\/em\u003e\u003c\/p\u003e","brand":"Mountain Hatch USA","offers":[{"title":"Black \/ Recessed pocket version","offer_id":50652296609984,"sku":"LC100-R-B","price":249.0,"currency_code":"USD","in_stock":true},{"title":"Black \/ Original flat version","offer_id":50652296642752,"sku":"LC100-OG-B","price":239.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0525\/3188\/8320\/files\/100seriesUSE.png?v=1793382227"},{"product_id":"15-26-ford-f150-mountain-hatch-tailgate-table","title":"Mountain Hatch Tailgate Cutting Board \u0026 Table for 2015-2026 Ford F-150 (13th \u0026 14th Gen)","description":"\u003cp\u003eThe Mountain Hatch Tailgate Table for the 2015-2026 Ford F-150 covers the aluminum-body thirteenth- and fourteenth-generation trucks with a 1\/2-inch food-grade HDPE panel that replaces the factory tailgate insert. Drink holders and a recessed utility tray are built into the slab.\u003c\/p\u003e\u003cp\u003eIt is a straight swap at the factory mounting locations: factory screws out, OEM panel off, Mountain Hatch on. The surface is food-safe and UV-stabilized, wipes clean, and protects the gate from the gear you throw in. If you have a tailgate step or work surface option, check that your panel is the standard insert before ordering. Mountain Hatch is a small shop in Riverside, California. Panels are machine-cut, hand-finished and made to order, which means a wait between ordering and the panel being ready.\u003c\/p\u003e\u003cp\u003eTwo trade-offs worth knowing. First, HDPE is cutting-board plastic: it scratches under a hard knife stroke and gets slippery when wet. Second, the panel adds weight to the tailgate, so the factory damper will let the gate drop a little faster than it did; Mountain Hatch is upfront that it stays controlled and does not slam. It is a work surface, not armor, so do not expect it to stiffen the gate.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eFits\u003c\/th\u003e\n\u003ctd\u003e2015-2020 Ford F-150 (13th Gen) and 2021-2026 Ford F-150 (14th Gen)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eVersions\u003c\/th\u003e\n\u003ctd\u003eRecessed version with drink holders and utility tray\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMaterial\u003c\/th\u003e\n\u003ctd\u003eHeavy-duty 1\/2-inch FDA-approved HDPE with UV inhibitors\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSurface\u003c\/th\u003e\n\u003ctd\u003eFood-safe, similar to a commercial cutting board\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eColor\u003c\/th\u003e\n\u003ctd\u003eBlack\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eInstallation\u003c\/th\u003e\n\u003ctd\u003eRemove factory screws and OEM tailgate panel, install Mountain Hatch, reinstall with appropriate hardware.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMade in\u003c\/th\u003e\n\u003ctd\u003eMade to order in Riverside, California, USA\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDesign\u003c\/th\u003e\n\u003ctd\u003eOriginal patented Mountain Hatch tailgate table\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eFitment and ordering\u003c\/h3\u003e\u003cp\u003eShop more for your truck in \u003ca href=\"\/collections\/f150-13th-gen\"\u003eF-150 13th Gen\u003c\/a\u003e and \u003ca href=\"\/collections\/f150-14th-gen\"\u003eF-150 14th Gen\u003c\/a\u003e, or see \u003ca href=\"\/collections\/mountain-hatch\"\u003eall Mountain Hatch panels\u003c\/a\u003e.\u003c\/p\u003e\u003cp\u003e\u003cem\u003eFitment: 2015-2026 Ford F-150. Confirm fit if your truck has the factory Tailgate Work Surface or integrated step.\u003c\/em\u003e\u003c\/p\u003e","brand":"Mountain Hatch USA","offers":[{"title":"Default Title","offer_id":50652296675520,"sku":"1526F150-R-B","price":249.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0525\/3188\/8320\/files\/F150_hatcj_69d35b7a-aff8-40e5-b8f9-50365fc3812e.png?v=1793382227"},{"product_id":"23-ford-f250-350-superduty-mountain-hatch-tailgate-table","title":"Mountain Hatch Tailgate Cutting Board \u0026 Table for 2023+ Ford F-250 \/ F-350 Super Duty","description":"\u003cp\u003eMountain Hatch's Tailgate Table for the 2023+ Ford F-250 and F-350 Super Duty is the newest Super Duty fitment: a 1\/2-inch food-grade HDPE panel in the recessed-pocket layout, with drink holders and a 1\/4-inch-deep utility tray. It replaces the factory tailgate panel at the stock mounting points and leaves the gate flat edge to edge.\u003c\/p\u003e\u003cp\u003eThe photos show it on a Tremor, where the black panel sits flush with the bed liner and the stamped MADE IN USA mark faces you when the gate is down. The surface is food-safe and UV-stabilized, and it protects the tailgate when the truck is working. Every panel is cut on CNC machinery and then finished by hand in Riverside, California, and built to order, so plan on some production time before it leaves the shop.\u003c\/p\u003e\u003cp\u003eWhat it is not: a rigid reinforcement for the tailgate, or a scratch-proof surface. Like any plastic cutting board it will show knife marks over time, and wet HDPE is slick, so keep an eye on a beer parked on a sloped campsite. The extra weight also means the factory damper lets the gate open a bit quicker than stock; Mountain Hatch says it will not slam, and that matches what owners report.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eFits\u003c\/th\u003e\n\u003ctd\u003e2023+ Ford F-250 and F-350 Super Duty\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eVersions\u003c\/th\u003e\n\u003ctd\u003eRecessed Pocket Version with drink holders and utility tray\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMaterial\u003c\/th\u003e\n\u003ctd\u003eHeavy-duty 1\/2-inch FDA-approved HDPE with UV inhibitors\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSurface\u003c\/th\u003e\n\u003ctd\u003eFood-safe, similar to a commercial cutting board\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eColor\u003c\/th\u003e\n\u003ctd\u003eBlack\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eInstallation\u003c\/th\u003e\n\u003ctd\u003eRemove the factory tailgate panel and install at the factory mounting locations.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMade in\u003c\/th\u003e\n\u003ctd\u003eMade to order in Riverside, California, USA\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDesign\u003c\/th\u003e\n\u003ctd\u003eOriginal patented Mountain Hatch tailgate table\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eFitment and ordering\u003c\/h3\u003e\u003cp\u003eShop the rest of \u003ca href=\"\/collections\/super-duty-2023\"\u003eFord Super Duty (2023+)\u003c\/a\u003e, or see \u003ca href=\"\/collections\/mountain-hatch\"\u003eall Mountain Hatch panels\u003c\/a\u003e.\u003c\/p\u003e\u003cp\u003e\u003cem\u003eFitment: 2023+ Ford Super Duty. Confirm fit if your truck has the factory tailgate step.\u003c\/em\u003e\u003c\/p\u003e","brand":"Mountain Hatch USA","offers":[{"title":"Black \/ Recessed Pocket Version New","offer_id":50652296773824,"sku":"23F250_R_B","price":249.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0525\/3188\/8320\/files\/use1.png?v=1793382236"},{"product_id":"ford-ranger-mountain-hatch-tailgate-platform-2024-2027","title":"Mountain Hatch Tailgate Cutting Board \u0026 Table for 2024+ Ford Ranger \u0026 Ranger Raptor","description":"\u003cp\u003eMountain Hatch's Tailgate Table for the 2024+ Ford Ranger, including the Ranger Raptor, replaces the factory tailgate access panel with a 1\/2-inch food-grade HDPE slab. The recessed-pocket layout puts two drink holders and a 1\/4-inch-deep utility tray at one end and leaves the rest flat for prep.\u003c\/p\u003e\u003cp\u003eMountain Hatch specifies no drilling: remove the factory access panel and install the Mountain Hatch at the factory mounting locations. The UV-stabilized surface is food-safe and textured, and it protects the gate from scratches and dents when gear goes in. Each panel is made to order in Riverside, California: the outline is machine-cut, then the edges and pockets are finished by hand, so allow production time.\u003c\/p\u003e\u003cp\u003eSet expectations before you buy. The surface is textured HDPE, which means it will take knife marks like a kitchen board and is slick when wet. The panel is not structural, so it protects the tailgate skin without reinforcing it. And the added weight lets the factory damper open the gate a touch faster than stock, though, as Mountain Hatch notes, it will not slam open.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eFits\u003c\/th\u003e\n\u003ctd\u003e2024+ Ford Ranger and Ranger Raptor\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eVersions\u003c\/th\u003e\n\u003ctd\u003eRecessed Pocket Version with drink holders and utility tray\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMaterial\u003c\/th\u003e\n\u003ctd\u003eHeavy-duty 1\/2-inch FDA-approved HDPE with UV inhibitors\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSurface\u003c\/th\u003e\n\u003ctd\u003eFood-safe, similar to a commercial cutting board\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eColor\u003c\/th\u003e\n\u003ctd\u003eBlack\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eInstallation\u003c\/th\u003e\n\u003ctd\u003eRemove the factory tailgate access panel and install at the factory mounting locations. No drilling.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMade in\u003c\/th\u003e\n\u003ctd\u003eMade to order in Riverside, California, USA\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDesign\u003c\/th\u003e\n\u003ctd\u003eOriginal patented Mountain Hatch tailgate table\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eFitment and ordering\u003c\/h3\u003e\u003cp\u003eKeep building in \u003ca href=\"\/collections\/ford-ranger-2024\"\u003eFord Ranger (2024+)\u003c\/a\u003e, or see \u003ca href=\"\/collections\/mountain-hatch\"\u003eall Mountain Hatch panels\u003c\/a\u003e.\u003c\/p\u003e\u003cp\u003e\u003cem\u003eFitment: 2024+ Ford Ranger only.\u003c\/em\u003e\u003c\/p\u003e","brand":"Mountain Hatch USA","offers":[{"title":"Black \/ Recessed Pocket Version New","offer_id":50652296806592,"sku":"6GRANGER-R-B","price":249.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0525\/3188\/8320\/files\/ranger_Use.png?v=1793382237"}],"url":"https:\/\/overlandkitted.com\/collections\/mountain-hatch.oembed","provider":"Overland Kitted","version":"1.0","type":"link"}